1
75⍀
ANT /
CABLE
2
VHFV
VHF
UHF
300Ω
75-300 Ω ADAPTER
OR
75⍀
ANT /
CABLE
HOOKING UP YOUR TV (ANTENNA/CABLE TV CONNECTIONS)
A
combination antenna
receives normal
broadcast channels (VHF
2-13 and UHF 14-69).
Your connection is easy
since there is only one
75Ω (ohm) antenna plug
on the back of your TV -
and that’s where the anten-
na goes.
ANTENNA
COMBINATION UHF/VHF
Remember,
be sure to set the
TV for the type sig-
nal you've connect-
ed (see page 3 of
this Set-Up Guide.)
To set the TV to
select only the
channel numbers in
your area see how
to “Program" or
"Add" channels in
memory on page 3.
To order any
optional accessory
contact your dealer
or call the toll-free
accessory ordering
number (1-800-292-
6066):
• UHF/VHF
Combiner:
(SBV1133AO1)
• 75-300 Ohm
Adapter:
(SBV1113AO1)
• 300-75 Ohm
Adapter:
(483521827003)
SMART
HELP
If your antenna has a
round cable (75 ohm) on the
end, then you're ready to con-
nect it to the TV.
If your antenna has flat twin-
lead wire (300 ohm), you first
need to attach the antenna wires
to the screws on a 300 to 75
ohm adapter.
Push the round end of the
adapter (or antenna) onto the
ANTENNA/CABLE plug on
the rear of the TV. If the round
end of the antenna wire is
threaded, screw it down tight.
S
ome of you may have
two separate antennas.
One antenna is for VHF
channels (2-13) and the
other antenna is for UHF
channels (14-69).
For homes with separate
UHF/VHF antennas, you
will need an optional
"combiner" before you can
connect to the TV. See the
"Smart Help" section (to
the right on this page) for
ordering details.
SEPARATE UHF/VHF
300 to 75Ω
Adapter
(483521827003)
Combination VHF/UHF Antenna
(Outdoor or Indoor)
Twin Lead
Wire
Round Cable
75Ω
Back of TV
Back of TV
U/V Combiner
75-300 Ohm Adapter
Outdoor UHF Antenna
(Twin-lead 300 Ohm)
Outdoor VHF Antenna
(Twin-lead 300 Ohm)
IN
OUT
1
75⍀
ANT /
CABLE
2
Y
our Cable TV input
into your home may be
a single (75 ohm) cable, or
a Converter Box installa-
tion. In either case the
connection to the TV is
very easy. Just put the
threaded end of the cable
signal to the TV's antenna
plug and screw it down
tight.
CABLE TV
CABLE INPUT/CONVERTER
OUT TO TV
IN FROM ANT.
75⍀
ANT /
CABLE
T
he basic Antenna, or
Cable TV, to VCR to
TV connection is shown to
the right. For more infor-
mation on other hookups
(possible when Cable
Converter/Descrambler
boxes are included) refer
to your accessory VCR
and Cable Converter
Owner's Manual for
details.
VCR TO TV
BASIC CONNECTION
Twin Lead
Wire
Round Cable 75Ω
If your Cable TV sig-
nal is a single round cable (75
ohm) then you're ready to con-
nect to the TV.
If you have a Cable TV
Converter Box:
Connect the Cable TV signal to
the Cable Signal IN(put) plug
on the Converter.
Connect the Cable TV
cable to the ANTENNA/CABLE
plug on the TV.
If you have a Cable TV
Converter Box:
Connect the OUT(put) plug
from the Converter to the
ANTENNA/CABLE plug on the
TV.
Push the round end of the combiner
onto the ANTENNA/CABLE plug on
the rear of the TV.
Attach the separate
UHF and VHF antennas to
the correct screws on the com-
biner.
BEGIN
BEGIN
BEGIN
Round
End
Connect your
Antenna or Cable TV signal
to the IN FROM ANT(enna)
plug on the VCR.
Connect the OUT TO TV
plug on the VCR to the
ANTENNA plug on the TV
(connecting cable supplied
with the VCR.)
BEGIN
Outdoor VHF Antenna
(Round 75 Ohm cable)
Back of TV
Round Cable
75Ω Ohm
Cable TV Converter
Box Connection
Cable TV Company
Remember,
set the TV for the
type signal you've
just connected (see
page 3 of this Set-
Up Guide.)
To select only the
channel numbers on
your Cable system
see “Auto Program"
(page 3). If you use
a Cable Converter
box, set the TV to
the same channel as
the converter's CH
3/4 switch (on the
rear of the convert-
er.)
SMART
HELP
Cable TV Signal Input
Round Cable
75Ω Supplied with VCR
Outdoor VHF/UHF
Antenna
300 to 75Ω Ohm
Adapter
Cable TV signal
Back of TV
Refer to the Owner's
Manual included with your
VCR for other possible con-
nections and TV/VCR operat-
ing details.
OR
NOTE: The connecting cable for
the Converter is supplied from
the Cable TV Company.
VCR
2 - IB7755 E001