Filter
Top Products
Mount it
Ask a friend to help out.An extra hand to hold the unit makes mounting easier and
quicker.
A
•
Cut the template to fit inside the cabinet.
• Align the template border marked "FRONT" along
the front edge of your cabinet.
• Use adhesive tape to fix the template.
• Drill 1/4 inch holes, as marked on the template.
• Remove the template when you finish drilling.
3
Tip
– Clean the bottom of the cabinet surface and also empty your cabinet
before mounting.
– Place the unit in a clean, safe place when drilling to avoid wood shav-
ings dropping into the ventilation slots.
– Use a nail to start each drill hole.
– Drill from the bottom upwards if you do not have enough room inside
the cabinet.
– Hold your drill firmly at 90
o
with the cabinet bottom and drill holes at
low speed.
– Clear wood shavings.
B
Using the spacers
A total of 16 spacers are supplied. Depending on the
thickness of your cabinet bottom (with or without an
overhang), you can select 4 spacers of the best length to
mount the set.
• Measure the height of the cabinet bottom and/or
overhang.
• Select 4 spacers of the optimum length.
• Insert the spacers accordingly.
C
• Manually fasten 4 long screws (selected according to
actual situation) down into the spacer holder holes to
mount your set. Start screwing at opposite corners of
the unit for better support.
Tip
To prevent damage to your set, do not use an
electric drill to secure screws when mounting!
Use it
For full details, please read and follow the instructions inside the User manual.
A
Power supply
• Connect the power plug to the wall outlet.
• Press POWER to switch on.
B
Using the LCD screen
• Pull out the LCD screen under the unit and swivel round as shown.
• To store away, swivel and tuck. Push back until you hear a click.
C
How to play a DVD /CD
• Select DVD source.
• Insert a DVD/CD.
• Press PLAY/PAUSE
2;
to start disc playback.
4
POWER
SUBTITLE
AUDIO
EJECT
DVD
TV
AV
1 2
3
4
5
6
7 8 9
+10 0
FM/AM
TV/LCD SETUP
DVD SETUP
GOTO
INFO
SET
OK
CH-
CH+
VOL
+
-
TIME
REPEAT
A-B
SLOW
ZOOM
RC 518B
SEEK
16:9/4:3
MENU TITLE
+
-
LCD
ON/OFF
MUTE
Insert DVD/CD
D
How to watch TV on the unit
• Ensure normal TV antenna and power cord connection.
• Switch on the system.
• Press TV on the remote control or SOURCE on the
front panel to switch to the TV mode.
• Enter TV SETUP.
• Press 3 / 4 to select Fine Tuning or Auto Memory to
store channels.
• After exiting TV SETUP, press 3 / 4 on the remote
control to select the desired channel, or use the
Numeric Keypad (0-9) for input and then press OK
for confirmation if necessary.
POWER
SUBTITLE
AUDIO
EJECT
DVD
TV
AV
1 2
3
4
5
6
7 8 9
+10 0
FM/AM
TV/LCD SETUP
DVD SETUP
GOTO
INFO
SET
OK
CH-
CH+
VOL
+
-
TIME
REPEAT
A-B
SLOW
ZOOM
RC 518B
SEEK
16:9/4:3
MENU TITLE
+
-
LCD
ON/OFF
LCD
ON/OFF
MUTE
E
Improve radio reception
FM: place the antenna as far as possible from the AC adaptor
to avoid interference.
AM: always mount the antenna vertically.
AM
270 maximum
115
Tip
– Swivel with care to avoid breakage. Screen rotates a
maximum 270
0
only.
Template
A
B
C
Mounting
Screw
MDR700 QUG-Eng 2/14/05 11:16 Page 2