30 EN30 EN
TIMER RECORDING
Note
• Press [TIMER PROG.] to check the timer recording in
progress.
When the timer recording is proceeding, that
program will be highlighted with red. In this case,
you cannot select any other program.
If the timer program did not complete correctly,
the error number appears in the timer
programming list.
Timer Programming
1/1
FRI JAN/07 11:00AM
Date Start End L1/L2
E41 JAN/07 12:00AM 1:00AM L1
New Program
Each error number means:
E1-22
E37-39
Recording error other
than below
E41 Power failed
E24 Unrecordable disc E42 No disc when
recording
E25-26 Copy prohibited
program
E43 Already 49 titles
recorded
E29 Disc protected E44 Already 254 chapters
recorded
E30 Disc full E45 Copy prohibited
program
E35 PCA full *
1
E46 It is impossible to
record additionally
on a disc recorded
by other units
when setting “
Make Recording
Compatible” to “OFF”.
E36 Already finalized
video format disc
E40 Some portion has
not been recorded
because of program
overlapping.
Recording did not
start at the start time.
• E23, E27, E28, E31, E32, E33 and E34 are not displayed.
• A program with the error number is grayed in the timer
programming list.
• Timer program with an error number will be cleared
once the entry screen for the program is displayed.
*
1
PCA is a disc's space reserved for recording test.
To stop the timer recording in progress
1) Press [STOP C ] on the remote control.
2) Confirmation message will appear. Select “Yes”,
then press [OK].
• To stop the timer recording immediately, press
[C STOP] on the unit.
Checking, canceling, or correcting the timer
programming information
1) Press [STANDBAY/ON y].
2) Press [TIMER PROG.].
3) Check the information.
Timer Programming
THU JAN/06 11:00AMSP (1:00)
JAN/ 7/11 12:00 AM L1 SP
Date Start End L1/L2
JAN/07 12:00AM 1:00AM L1
New Program
4-A) To delete the timer program:
1 Use [K / L] to select the program you want to
delete, then press [OK].
2 Use [K / L] to select “Delete”, then press [OK].
Confirmation window will appear.
3 Use [K / L] to select “Yes”, then press [OK].
4-B) To correct the timer program:
1 Use [K / L] to select the program you want to
correct, then press [OK].
2 Use [K / L] to select “Program Change”, then
press [OK].
3 Correct the timer program by using
[K / L / { / B], then press [OK].
5) Press [TIMER PROG.] to exit.
6) Press [STANDBAY/ON
y] to return to the timer
standby mode.
Putting Names on Timer Programs
1) In stop mode, press [TIMER PROG.].
2) Use [K / L] to select the program you want to edit
the timer program name, then press [OK].
3) Use [K / L] to select “Edit Title Name”, then press
[OK].
Program Change
Delete
Edit Title Name
A window for entering a title name will appear.
Timer Programming Edit Title Name
1/1
THU FEB/03 11:30AMSP (1:00)
Date Start End L1/L2
JAN/07 12:00A L1
a b c
A B C
1 2 3
@! ?
FEB/05/11 10:30 AM L1 SP
4) To enter a title name, follow the steps of “Guide to
Edit Title Name” on page 58.
5) After entering a title name, press [OK].
6) Use [K / L] to select “Yes”, then press [OK].
• The program name is now updated.
