Marshall electronic V-R1042DP-TE4U Flat Panel Television User Manual


  Open as PDF
of 4
 
Marshall Electronics
4
5
Electrical Specications
Display (Viewing Area) 10.4 Inch diagonal (211.2mm W x 158.4mm H)
Screen Aspect Native 4:3, Switchable to 16:9
Resolution (RGB Dots) 1024HxRGx768V (2.4 Million Pixels)
Viewing Angles 170°H x 170°V
Contrast Ratio 400:1
Dot Pitch 0.206mm square pixel
Pixel Response 13ms rise /12ms fall
Brightness 400 cd/m²
Backlight Field Replaceable CCFL (50,000 hour half life)
Screen Treatments Anti Reflection, Anti Glare, Hard Coat
Protective Screen 0.118” (3mm) thick Optical Grade Polycarbonate with Anti-Glare and Anti-Abrasion
coatings. (600 Cheesecloth mil-M-13508C)
Estimated MTBF 5 years of 24/7 operation
Inputs 1 SDI/HDSDI input per screen; SMPTE 259M-C, 292M / ITU-R BT.601; female BNC;
1080i/60,59.95,50; 1080psF/24,23.98; 1035i/60,59.94; 720p/60,59.94,50,30,29.97,25
Active Outputs 1 SDI/HDSDI output per screen; SMPTE 259M-C, 292M / ITU-R BT.601; female BNC
Tally 2 LEDs (Green, Red) per monitor; female HD-15 connector
Color temperature D65 (6500° Kelvin)
Color Gamut SMPTE-C/EBU
Luma Linearity Typical +/- 3% with 5 ire increments (0 to 10 ire)
Power Required 10.4 to 16.8 VDC
Power Consumption 36 watt nominal for V-R1042DP-TE
Operating Temperature 32°F to 120°F (0°C to 50°C)
Storage Temperature -4°F to 120°F (-20°C to 50°C)
Compliance
₠, FCC-Class A, ANSI-63.4 (Certificates on file)
RoHS WEEE/Environmental Do not dispose. Return to Manufacturer or Authorized Recycle Facility
V-PS12-5V-1 Power Supply 14-10 VDC (Universal Voltage 5.0Amps max - UL Class 2 supply included)
6
Mechanical Specication
V-R1042DP-TE4U V-PS12-5V-1 Power Supply
Dimensions (W x H x D)
(Main body only)
18.9” x 7.0” x 1.6” 4.13” x 2.50” x 1.25”
Approx. Weight 5.0 lbs 0.65 lbs
7
Faceplate Cleaning
Faceplate Cleaning
When cleaning the faceplate it is very important to use non-abrasive and ammonia free cleaning agents and a clean micro ber
cloth. Do not use paper towels. Paper towel bers are coarse and may scratch the surface of the Polycarbonate faceplate.
Paper towels may also leave streaks on the surface. Antistatic and ngerprint resistant cleaning agents are recommended.
Wash protective cover with a solution of mild soap or detergent and lukewarm water. Use a clean soft cloth, applying only light pres-
sure. Rinse with clean water and dry by blotting with a damp cloth or chamois. Grease, oil or tar may be removed with a good grade
of hexane, aliphatic naphtha, or kerosene. These solvents may be obtained at a paint or hardware store and should be used in ac-
cordance with manufacturer’s recommendations.
DO NOT USE: window cleaning sprays, kitchen scouring compounds or solvents such as acetone, gasoline, benzene,
alcohol, carbon tetrachloride, or lacquer thinner. These can scratch the sheet’s surface and/or weaken the sheet causing
small surface cracks called “crazing.”
Faceplate Dusting
Dust with a soft, damp cloth or chamois. Dry or gritty cloths may cause surface scratches and create a static electric charge on the
surface. Neutralizing static electricity effects by using recommended cleaning and polishing practice.
Faceplate Polishing
Protect and maintain surface gloss by occasional polishing with a good plastic cleaner and polish. Apply a thin, even coat with a soft
clean cloth and polish lightly with cotton annel. Then wipe with a damp cloth to help eliminate electrostatic charges that can attract
dust particles.
Marking on the Faceplate
Use SHARPEE or equivalent marker. Clean as per instructions with an ammonia free cleaning agent.
V-R1042DP-TE4U User’s Guide
 previous