11
ENGLISH
TROUBLESHOOTING GUIDE
Before requesting service, please refer to the following chart for the symptom and possible solution.
SYMPTOMS POSSIBLE SOLUTIONS
• Make sure the power cord is plugged in.
• Try another AC outlet.
• Power is off, check fuse or circuit breaker.
• Unplug unit for an hour, then plug it back in.
• Station or CATV experiencing problems,
tune to another station.
• Check sound adjustments (Volume and Muting).
• Check for sources of possible interference.
• Station or CATV experiencing problems,
tune to another station.
• Make sure channels are set into memory.
• Check antenna or CATV connections, adjust
antenna.
• Check for sources of possible interference.
• Check picture control adjustments.
• Station or CATV experiencing problems,
tune to another station.
• Make sure channels are set into memory.
• Station is weak, adjust antenna to receive
desired station.
• Check for sources of possible interference.
• Station or CATV experiencing problems,
tune to another station.
• Make sure channels are set into memory.
• Check picture control adjustments.
• Check antenna or CATV connections, adjust
antenna.
• Check for sources of possible interference.
• Station or CATV experiencing problems,
tune to another station.
• Make sure channels are set into memory.
• CATV company is scrambling signal.
• Adjust antenna.
• Check all CATV connections.
• Set TV/CATV menu option to the CATV mode.
• Station or CATV system problems, try
another station.
• Check antenna connections, adjust or
re-direct antenna.
• Check for sources of possible interference.
Poor sound
or No sound.
Poor picture
or No picture.
Horizontal or
diagonal bars
on screen.
No Remote
operation.
• Select proper language in the menu options.
Display is not
shown in your
language.
No reception
above
channel 13.
No CATV
reception.
• Batteries are weak, dead or inserted incorrectly.
• Remote is out of range, move closer to TV
(within 15 feet).
• Make sure Remote is aimed at sensor.
• Confirm there are no obstructions between
the Remote and the TV.
• Make sure the power cord is plugged in.
• Make sure TV/CATV menu option is in the
appropriate mode.
•
If using antenna, check UHF antenna connections.
• No broadcast on station tuned.
• Sleep Timer is set.
• Power interrupted.
TV shuts off.
• TV station experiencing problems or program
tuned is not closed captioned. Try another channel.
• Check CATV connection or VHF/UHF
antenna, reposition or rotate antenna.
• Press TV/CAP/TEXT button to turn on the
closed caption decoder.
Closed -
Caption is
not activated.
SYMPTOMS
POSSIBLE SOLUTIONS
TV does not
operate.
Picture
wobbles or
drifts.
Poor color or
no color.
Poor
reception on
some
channels.
• Reset your password.
No reception.
SPECIFICATIONS
AC Power Input:
AC Power Consumption:
Chassis Construction:
Picture Tube:
Horizontal resolution:
Audio Power Output Rating:
Speakers:
Tuner Type:
Remote Control:
120 V, 60 Hz
125 Watts
IC Solid state
27 inches (measured diagonally)
260 lines
2.5 + 2.5 Watts
2 inches x 3-1/2 inches Full
Range, 8 ohms x 2
181 Channel, Quartz PLL
Frequency Synthesized
Infrared, Direct Access, 2 x AAA
batteries (not supplied)
Remote Control
ACCESSORY
Receiving Channels:
Antenna Input Impedance:
Input/Output:
Dimensions:
Weight:
VHF 2-13
UHF 14-69
CATV 01-97 (5A)-(A-3)
98-99 (A-2)-(A-1)
14-22 (A)-(I)
23-36 (J)-(W)
37-65 (AA)-(FFF)
66-125 (GGG)-(125)
75 ohm (VHF/UHF/CATV)
Coaxial Input
S-Video Y-Input : 1.0 Vp-p/75 ohms
C-Input : 0.3 Vp-p/75 ohms
Video: In (RCA) 1.0 Vp-p/75 ohms
Out (RCA) 1.0 Vp-p/75 ohms
Audio: In (RCA) –8 dB/50K ohms
Out (RCA) –8 dB/1K ohms
25-9/16 (W) x 19-11/16 (D) x 22-1/2
(H) inches
80.5 Ibs
DEGAUSSING SYSTEM
This television has a degaussing circuit that will clear up color distortions on the TV screen that are caused by any excess
magnetism which happens to get too close to the TV. This circuit is designed to operate once when the set is first plugged in. If
minor color distortions are seen in some locations on the screen, please unplug the TV for approximately 15 minutes. When the
TV is plugged back in, the degaussing circuit will operate once to clear up any color distortions. Repeat this procedure any time
the TV screen is accidentally magnetized, or when the TV is moved or relocated.
Design and specifications are subject to change without notice.
3T10921A-E 1/14/05, 14:0611