Filter
Top Products
INSTALLING THE REMOTE CONTROL’S BATTERY
LOCATION OF CONTROLS
CONNECTIONS
1234
5
6
7
1. AC Power Cord
2. HDMI Jack
3. Component Video (Y, PB, PR) Output
Jacks
AV Cable Part No. 043-28102-533-001*
4. Coaxial Digital Audio Output Jack
5. S-Video Output Jack
6. Audio Left/Right Output Jacks
7. Video Output Jack
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Warning–Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type.
2. Use only the size and type of batteries specified.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery
compartment. Reversed batteries may cause damage to the device.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage
or injury from possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
(Follow battery manufacturer’s directions.)
Connecting the DVD to a Home Theater System
Place the subwoofer, front, rear and center speakers in locations as shown/described here.
After correctly positioning the speakers, perform the Tone Test on the AV Amplifier and
adjust the volume controls until the desired sound is achieved. For best results, sit in the
viewing position and have someone adjust the volumes for you; this will enable you to set
the optimal levels.
1. Front Left Speaker
2. Television
3. Center Speaker–can be
located on top or below the
Television.
4. Sub-woofer–can be located
anywhere in the room.
5. Front Right Speaker
6. Viewing/Listening
Position–The best listening
position is obtained by
positioning the chair, sofa,
etc. in the middle of all the
speakers.
7. Rear Left Speaker
8. Rear Right Speaker
9. AV Amplifier w/Dolby
Digital Decoder/DTS
Decoder
1 2 3 4567 8910
15
2
3
5
4
7
9
11
23
24
22
20
18
19
17
16
1
6
8
10
12
13
21
14
1. Disc Compartment
2. OPEN/CLOSE Button
3. Display
4. Play/Pause ®p Button
5. Stop X Button
6. Skip/Search Down (o) Button
7. Skip/Search Up (n) Button
8. Remote Sensor
9. Power Button
10.ON/STANDBY Indicator
Replacing the Remote Batteries
1. Remove the battery cover by pressing in on the tab and the lifting the cover off.
2. Insert a CR2025 button-type battery into the battery compartment with the “+” facing
up. Replace the battery cover.
1. HDMI/PS Button
2. STANDBY ON/OFF Button
3. Number Buttons
4. REV (Reverse) (M) Button
5. OPEN/CLOSE Button
6. Navigation (π) Button
7. ANGLE Button
8. ENTER/PLAY ® Button
9. Navigation (√)/SKIP (o) Button
10. Navigation (†) Button
11. SEARCH Button
12. TITLE/RETURN Button
13. SUBTITLE Button
14. DISPLAY Button
15. MUTE Button
16. REPEAT/A-B Button
17. PAUSE/STEP Button
18. FWD (Forward) (l) Button
19. STOP (■) Button
20. ZOOM Button
21. Navigation (®)/SKIP (n) Button
22. SETUP Button
23. AUDIO Button
24. DVD MENU/PBC Button
REMOTE PART NO. HS-MVD2047-BLK-320*
*Consumer Replaceable Part (See bottom of page 4 to order.)
ADVANCED PLAYBACK OPTIONS
FRONT
REAR
REMOTE
3
2
NOTES FOR CONNECTING TO A TV:
• If your TV has an HDMI input, connect the DVD player with the component cable for best results,
otherwise use the Component, S-Video or Video OUT jack on the DVD player.
• Set the TV’s TV/VIDEO button or switch to the VIDEO setting.
• When connecting the DVD, refer to the owner’s manuals for the TV and the audio system, as well
as this manual.
• When connecting, make sure the power is off and all units are unplugged before making any
connections.
• Connect the DVD player to your TV directly. If you connect the DVD player through a VCR, the
playback picture will be distorted because DVD video discs are copy protected.
• If using a TV with a blue screen option, turn the option off for best results.
• If you place the DVD player near a tuner, the radio broadcast sound might be distorted. In this
case, move the DVD player away from the tuner.
BASIC PLAYBACK OPTIONS
BASIC PLAYBACK OPTIONS (CONTINUED)
DVD/CD/VCD BASIC OPERATION
1. Plug the power cord into the outlet once the DVD player is connected to your TV.
2. Turn on the TV and tune to its Video Input Channel, if necessary.
3. Press the STANDBY button on the remote or the Power button on the main unit to turn
on the unit; the On/Standby indicator will turn off.
4. Press the OPEN/CLOSE button to open the disc tray. Insert a disc with the label side
facing up on the disc tray. Press the OPEN/CLOSE button again to close the tray;
playback will start automatically.
5. If the Menu appears, use the Navigation (√, ®, π, †) buttons to select the desired
option and press the ENTER/PLAY ® button to select it.
6. To stop playback, press the STOP (■) button. Because the unit will remember where
you stopped (not applicable in CD mode), simply press the ENTER/PLAY ® button to
resume playback where you left off (resuming playback). If the STOP (■) button is
pressed twice, the unit will stop completely. If the player is left in Stop/Pause mode for
more than one minute without any user interaction, the screen saver will activate if the
Screen Saver menu option is set to ON. There is no resume function when playing CDs.
SEARCH FORWARD/REVERSE: During playback, press the FWD ®® or REV √√
button to move the disc forward or backward at double (x2) speed to locate a specific
section. Repeatedly press and the speed will increase to x4, x8, x16 and resume normal
playback.
NOTE: The disc will move forward or backward at high speed until you press the
ENTER/PLAY ® button; normal playback will resume at that point.
PAUSE AND STEP: Press the PAUSE/STEP button while in the Play mode to pause the
picture. To advance one frame at a time, press the PAUSE/STEP button repeatedly. To
resume normal playback, press the ENTER/PLAY ® button.
SKIP: Press the Skip (n) button to advance the disc to the beginning of the next
chapter/track. Press the Skip (o) button to move the disc to the beginning of the previous
chapter/track.
ZOOM: Press the ZOOM button once during Normal or Still playback modes, and the unit
will zoom x2. Press once or twice more and the unit will zoom x3 or x4. Use the
Navigation (√,®,π,†) buttons to move the image on the TV screen. Press the ZOOM
button once more to cancel the zoom function. This is not available on all discs.
SLOW FORWARD AND REVERSE: Press the PAUSE/STEP button to pause the
playback, then repeatedly press the FWD ®® button to move the DVD forward in slow
motion speeds of 1/2, 1/4, 1/8, 1/16 and resume normal playback. Repeatedly press the
REV √√ button to move the DVD backward in slow motion speeds of 1/2, 1/4, 1/8, 1/16
and resume normal playback. The sound will be muted. You can also press the
ENTER/PLAY ® button to resume normal playback.
1st press
2nd press
3rd press
4th press
5th press
DVD
Title Elapsed Time
Title Remaining Time
Chapter Elapsed Time
Chapter Remaining Time
Off
CD/VCD
Single Elapsed Time
Single Remaining Time
Total Elapsed Time
Total Remaining Time
Off
MP3: Press the DISPLAY button to select between the Track Elapsed Time and Track
Remaining Time.
NOTE: For VCD, if the PBC is on, the Total Elapsed Time and Total Remaining Time will
not be available.
PLAYBACK MODES
Repeat Playback
While the disc is playing, press REPEAT/A-B button repeatedly to select a play mode:
DVD play modes: Chapter repeat, Title repeat, A-B Repeat, Off
CD play modes: Track repeat, All track repeat, A-B Repeat, Off
VCD Mode (PBC control must be off): Track repeat, All track repeat, A-B Repeat, Off
MP3 Mode: Track repeat, Folder repeat, Folder
A-B Repeat
To repeat a segment between two points (A and B), press the REPEAT/A-B button three
times to define the segment you want to repeat. Allow the disc to play to the end of the
segment or use FORWARD to advance to the end point (B). Press the REPEAT/A-B
button again at the end of the segment. The segment plays repeatedly until you press
REPEAT/A-B to resume normal playback.
ANGLE MARK: While in the Playback mode, press the ANGLE button; the total number
of angles will appear on the screen. Repeatedly press the ANGLE button to select the
desired angle; the angle will change in one to two seconds.
This is not available on all discs.
AUDIO (DVD AND VCD): Some discs have several audio tracks used for different
languages or different audio formats. To change the language or audio format during
play, press the AUDIO button one or more times to select one of the available audio
formats or languages. For VCD select (Mono-left, Mono-right, Mix-mono, Stereo).
Note: This option is only available if the disc offers a number of languages or formats.
PLAYBACK CONTROL (PBC): The Playback Control feature is available only on Video
CDs. Press the DVD MENU/PBC button to turn the PBC feature on and off. The Play-
back Control feature supports the menus of the VCD format similar to a DVD menu.
MUTE: To mute the playback sound, press the MUTE button.
SUBTITLE MENU: Press the SUBTITLE menu button to select a subtitle language and
the turn the subtitle menu on/off if your subtitle feature is available on the disc.
TITLE MENU: To display the title menu if available on the disc press the
TITLE/RETURN menu button. Then use the Navigation (√,®,π,†) buttons to select
your desired option and press ENTER/PLAY ® button.
DISPLAY BUTTON: Each press of the DISPLAY button will display the elapsed time and
remaining time of a playing disc. Each press of the DISPLAY button will cycle through,
depending on the playback mode, as follows:
TITLE/CHAPTER SEARCH (DVD ONLY): Press the SEARCH button once. Press the
Navigation (√,®) buttons to select Title, then use the Number buttons to select the
desired title number (i.e. for number 5, press “05”). Playback will start immediately. OR
Press the Navigation (√,®) buttons to select the Chapter, then use the Number
buttons to select the desired chapter number (i.e. for number 2, press “02”). Playback
will start immediately.
TITLE/CHAPTER/TIME SEARCH (DVD ONLY): Press the SEARCH button twice.
Press the Navigation (√,®) buttons to select Title, then use the Number buttons to
select the desired title number (i.e. for number 5, press “05”). Playback will start
immediately. OR
Press the Navigation (√,®) buttons to select the Title Time, then use the Number
buttons to select the desired Title Time (Hour/Minutes/Seconds); playback will start
immediately. Press the SEARCH button a third time. Press the Navigation (√,®)
buttons to select the Chapter, then use the Number buttons to select the desired
chapter number (i.e. for number 5, press “05”). Playback will start immediately. OR
Press the Navigation (√,®) buttons to select the Chapter Time, then use the Number
buttons to select the desired Chapter Time (Hour/Minutes/Seconds); playback will start
immediately.
PLAYING DISCS
Compatible Discs
This DVD player is capable of playing the following types of discs: DVDs, DVD+/- R,
DVD+/- RW, Audio CDs, Video CDs, CD/CD-R/RW with MP3 files, MPEG4 and Kodak
Picture CDs. Before you insert a disc in the player, make sure it is compatible.
You cannot play the following types of discs: laser Discs, CD-I, CD-ROM (computer discs),
DVD-ROM or discs recorded using other broadcast standards (i.e. PAL or SECAM) or CD-
G discs.
NOTE: Some discs may not be compatible due to laser pickup, recording formats and
software used. Some technologies and methods used for MP3 file recording on CD-R/RWs
can prevent optimal playback of these files by degrading the sound quality and/or the
ability for the player to read the file.
Regional Coding
Both the DVD Player and the discs are coded by region. These regional codes must match
in order for the disc to play. The region code for this DVD player is listed on the back of the
player.
KODAK PICTURE CD
DVD Player
INPUT
AUD IOVIDEO
LR
TV
Red
Yellow
White
Connection DVD to TV
NOTE: When connecting the
system cables, turn off the
power and make certain the
AC cord has been removed
from the wall outlet. See figure
on previous page.
1. Connect the Left and Right audio cables to the Left and Right AUDIO OUT jacks on the
rear of the DVD player. Connect the other ends to the Left and Right IN jacks on the TV.
You can also use the Coaxial Digital Out as described below.
2. Connect the video cable (Select one of the following connections for video.)
(GOOD) BASIC: Connect the video cable to the VIDEO OUT jack on the rear of the DVD
player. Connect the other end to the VIDEO IN jack on the TV.
(VERY GOOD) S-VIDEO (not shown): Connect the S-Video cable to the S-VIDEO jack
on the rear of the DVD player. Connect the other end to the S-VIDEO jack on the TV.
(BETTER) PROGRESSIVE (Y, PB, PR) VIDEO OUT:
Use these jacks to connect to a TV with progressive
video input jacks, press the HDMI/PS button to select
the compatible resolution of the TV. Progressive scan
is a video scanning system that displays all lines in a
frame in one pass, as opposed to the traditional
system, interlaced scan. This connection provides
optimum quality. To ensure maximum picture quality, use three video-grade cables for
connections. Note that it is essential to match the color-coded connectors with a
compatible TV.
NOTE: IF THE TV SCREEN IS BLANK, PRESS THE HDMI/PS BUTTON REPEATEDLY
UNTIL THE PICTURE APPEARS ON THE SCREEN AGAIN.
(BEST) HDMI (not shown): Connect an HDMI cable (Not included) to the HDMI jack on
the rear of the DVD player. Connect the other end to the HDMI IN jack on the TV. HDMI
transfers audio and video signals, so if using HDMI, there is no need to connect to audio
separately. Press the HDMI/PS button to select the compatible resolution of the TV.
IMPORTANT HDMI NOTE: When using HDMI as your video source, setup the HDMI in the
General Setup Menu as described later in this manual. If your TV does not have Audio and
Video input jacks and only has an RF jack, you need to connect an FR modulator (not
provided).
DVD Player
Yellow
White
Red
TV
VIDEO
L
AUDIO
R
Y
P
B
P
R
COMPONENT VIDEO OUT
Component Video Cables