Nuvo NV-LRC1 Universal Remote User Manual


 
6. If the device responds, go to step 6. If the device does not respond,
press CH+. The remote will try the next code. Continue until the device
responds.
NOTE: Press CH- to try the previous code.
7. To set the code, press SETUP once. The LED blinks twice.
8. To search for other device codes, repeat steps 1 to 6.
Checking The Codes
If you have set up the remote using the procedure in “Searching For Your
Code”, you may need to find out which five-digit code is operating your
equipment.
For example, to find out which code is assigned to your TV:
1. Press SOURCE 1 once.
2. Press and hold SETUP until the red LED blinks twice, then release.
3. Enter 990. The LED blinks twice.
4. To view the code for the first digit, press numeric key 1. Count the LED
blinks (for example, three blinks = 3), and write down the number in
the appropriate code listing in step 8 under “Programming a Device”.
NOTE: If a code digit is 0, the LED does not blink.
5. Repeat step 4 for the four remaining digits, using 2 for the second
digit, 3 for the third digit, 4 for the fourth digit, and 5 for the fifth
digit.
6. To check for other device codes, repeat steps 1-5, substituting
Sources 2-6.
Changing Volume Lock
The NV-LRC1 comes preset to allow independent volume control of each
selected device (Global Volume Unlock). However, you may change the
Volume Lock setting to Global Volume Lock so that one source’s volume
will control volume in all other modes. After that, you can perform
Individual Volume Unlock on a selected source to set its volume control
for independent operation or Global Volume Unlock to remove all volume
locking.
Locking Volume Control to One Mode (Global Volume Lock)
1. Press and hold SETUP until red LED blinks twice, then release.
2. Enter 993 and then press the mode key for the source you want to
control volume (for example, CD). The LED blinks twice. Now, when
you press VOL+, VOL- or Mute, the selected source (for example, CD)
will control the volume regardless of the current mode.
Unlocking All Volume Control (Restoring Global Unlock)
1. Press and hold SETUP until the red LED blinks twice, then release.
2. Enter 993 and then press VOL+. The LED blinks four times. Volume is
independently controlled for all programmed sources.
Unlocking a Single Source’s Volume Control
1. Press a source key (1-6).
2. Press and hold SETUP until the red LED blinks twice, then release.
3. Enter 993 and then press VOL-. The LED blinks four times. Volume is
independently controlled for the selected sources.
Programming Macros
A macro can be used to control a home theater operation, to set a
favorite channel, or for other multiple functions you would like to
control with one key press. You can use any key to activate a macro.
Moreover, each Macro Key can hold up to 32 key presses total.
You can program a macro that will operate regardless of what mode you
are in, or one that will only operate when you are in a specific mode.
NOTE: Programming a new macro over an existing one will erase the
original macro.
Programming a Mode-Independent Macro
1. Press and hold SETUP until the red LED blinks twice, then release.
2. Press 995. The LED blinks twice.
3. Press the key you want to use to activate your macro (POWER, any
unused key, etc.).
4. Enter the series of commands you want the macro to execute (up to 32
commands).
5.Press and hold SETUP until the red LED blinks twice, then release.
Now, when you press the Macro key, the remote will send the series of
commands you have entered, regardless of what mode you are in. For
example, you could program the Macro key to turn on both your TV and
cable box and select a particular channel.
To clear the macro, repeat steps 1 to 5 above, but do not enter a series of
commands at step 4.
Programming a Mode-Dependent Macro
1. Press a source key (1-6).
2. Press and hold SETUP until the red LED blinks twice.
3. Press 978. The LED blinks twice.
4. Press the key you want to use to activate your macro (POWER, any
unused key, etc.).
5. Enter the series of commands you want the macro to execute (up to 32
commands).
6. Press and hold SETUP until the red LED blinks twice, then release.
3
Directly enter channels
(For example, 09 or 31).
Press ENTER to send channel
number entries on some TV
models.
Macro device keys can be used to
dedicate multiple string macro
commands.
Whole-Home Control is dedicated
control of your NuVo System.
MUTE, VOL-, VOL+, ON/OFF
duplicate the NuVo zone keypad
functions.
Press this key...
To...
Programming a Device
To control devices, 1-6, follow these steps.
Before proceeding, find the codes for the devices you want to program in
“Manufacturer’s Codes” in the following pages and write them down or
highlight them.
NOTE: Any device may be set up on any mode key.
2
M1
Whole-Home Control
1. Turn on the device (for example, CD player) and, if needed, load
media (for example, a CD).
2. Press a device key (1-6).
3. Press and hold SETUP until the red LED blinks twice, then release.
4. Enter the first five-digit code for your device. The red LED blinks once
as each digit is entered. If the code is correct, the LED blinks twice.
NOTE: If the LED does not blink twice, repeat steps 2 to 4 and try entering
the code again.
5. Aim the remote at the device and press POWER. The device should
turn off. If it does not, repeat steps 3 to 5, trying each code for your
brand until you find one that works. If you cannot find a code that
works, see “Searching For Your Code”.
6. Repeat steps 1 to 5 for the other devices you want to control. For
Future reference, write down each working device code below:
Searching For Your Code
If your device does not respond to the remote after trying all codes
listed for your brand, or if your brand is not listed, try searching for your
code:
1. Press a device key once.
2. Press and hold SETUP until the red LED blinks twice, then release.
3. Enter 991. The LED blinks twice.
4. Enter the device group number:
5. Select a test function, such as POWER or PLAY. The remote sends IR
codes from its library to the selected device, starting with the most
popular code first.
SOURCE 1 Code:
Desc. _______
SOURCE 2 Code:
Desc. _______
SOURCE 3 Code:
Desc. _______
SOURCE 4 Code:
Desc. _______
SOURCE 5 Code:
Desc. _______
SOURCE 6 Code:
Desc. _______
TV (TVs)
VCR (VCRs, DVD players )
0
Cable (Cable Converters, Video Accessories, Satellite
Receivers).
1
2
Audio (Audio Amplifiers, Audio Amp/Tuners, CD players)
Code
Device Group
M2
M3
M4
M5
M6
M7
M8
MUTE
VOL-
VOL+
ON/OFF
3