Filter
Top Products
2 3 4
1
4
RECEIVER
RECEIVER
TRANSMITTER
D
VD-R / VCR
CBL / SAT
RECEIVER
5
3
TRANSMITTER
T
RANSMITTER
RECEIVER
TRANSMITTER
OFF OFF
ON ON
5
-10cm
Make sure that both the TRANSMITTER and RECEIVER
are switched off.
Put both "RECEIVER" and "TRANSMITTER" on the same
channel by using the slide switch on the back side of the units
Connecting the TRANSMITTER unit
U
se the AV cable(s) labeled “TRANSMITTER” to Connect the
T
RANSMITTER UNIT to the source device(s) (e.g. VCR/DVD-Recorder,
Cable/Satellite Receiver). Make sure that the SCART is connected to
the correct Output of the device, normally called “Line Out”.
If you wish to remotely control the source device (satellite receiver, video
recorder, camcorder, DVD player, digital or analogue Set-Top Box or Pay-TV
decoder box) from another room, for example to change channels on your
satellite receiver, you will need to:
Place the TRANSMITTER next/close to the source device and connect
the IR eye to the TRANSMITTER. Place the IR eye in front of the source
device(s). Make sure there is no interference of the IR Eye signal going
to the IR receiver of the source device(s).
Now, insert the adapter plug into the connector on the backside.
Connecting the RECEIVER unit
Use the AV cable labeled “RECEIVER” to Connect the
RECEIVER UNIT to the destination devic (e.g. TV). Make sure that
the SCART is connected to the correct Input of the device,
normally called “Line In”.
Insert the adapter plug into the connector on the backside.
If you want to control the source device, place the RECEIVER on top or
beside the destination device where it is able to catch the IR command from
your remote control.
Now that both units are connected you can switch ON the units using
the ON/OFF switch. The red LED on the front should light up. Place the
units as high as possible to avoid interference of any kind.
InstallationInstallation
1
2
3
4
5
The Audio Video Sender (SV-1725) is a solution for distributing audio and
video signals to every place in the house without the need of wires. The
AV Sender gives you the possibility to view any video source (satellite
r
eceiver, video recorder, camcorder, DVD player, digital or analogue
Set-Top Box or Pay-TV decoder box) on your second TV in your home.
The One For All AV Sender (SV-1725) package contains:
-
TRANSMITTER unit
-
RECEIVER unit
- Infra-red (IR) Eye
-
Two Power adapters
-
Three “AV” cables (2 for TRANSMITTER and 1 for RECEIVER)
The TRANSMITTER sends the audio and video signals from the source
d
evice(s) (VCR, DVD, SATELLITE/ CABLE BOX, CAMCORDER, etc) by 2.4 GHz
t
o the RECEIVER that is connected to the destination device. The built in
Remote Control Extender sends the IR signal in the opposite direction
(from RECEIVER unit to TRANSMITTER unit) at a frequency of 433.92 MHz.
TRANSMITTER unit
The TRANSMITTER operates on 9 Volts DC 300mA that is supplied by the
AC/DC Adapter (included in package). Connecting from the audio or video
device to the TRANSMITTER is done by the included AV cable labeled
"transmitter"). The Audio and/or video signals are transformed to a
2.4GHz frequency that will be sent via the built-in antenna.
Furthermore the TRANSMITTER transforms the Remote Control Extender
signal (at 433.92 MHz) back to an IR command.
RECEIVER unit
The RECEIVER operates on 9 Volts DC 300mA that is supplied by the AC/DC
Adapter (included in package). Connecting from the audio or video device
to the RECEIVER is done by the included AV cable "Receiver". The high
frequency signal (2.4GHz) received by this unit are captured by
the built-in antenna of the RECEIVER unit and will be transformed into the
original audio and video signals.
Secondly the RECEIVER has a built in remote control extender. When an
infra red signal is Received by the RECEIVER, it will transform the IR
command to 433.92 MHz and can be sent through walls and ceilings.
Please note that this feature is only accessible for devices that are
controlled via IR (infra-red) signals at a frequency of 30 - 60 kHz
This feature does not support the 2-way IRDA waveform. If you are unsure
of the details of the remote control (IR) output, please refer to the manual
of the original device or contact your cable supplier.
The Product
Declarationof Conformity
We, Universal Electronics Inc., 6101 Gateway Drive, Cypress, CA 90630, U.S.A., and its subsidiaries
Universal Electronics BV, Institutenweg 21, 7521 PH Enschede, Netherlands,
ONE FOR ALL GmbH, Fabrikstra_e 3, 48599 Gronau, Germany,
ONE FOR ALL UK Ltd, Institutenweg 21, 7521 PH Enschede, Netherlands,
ONE FOR ALL FRANCE S.A.S., Rue Paul Séramy 17, 77300 Fontainebleau, France,
ONE FOR ALL IBERIA S.L., Ctra. Hospitalet, 147-149, 08940 Cornellá de Llobregat, Barcelona, España,
ONE FOR ALL ARGENTINA S.R.L., AV. Las Heras2126, 5th Floor (Suite “C”)
ZC 1111, Recoleta, Buenos Aires, Argentina
Universal Electronics Italia S.r.l., Via Cerva, 18, 20122 Milano, Italia
Declare under sole responsibility that the ONE FOR ALL Wireless Audio/Video Sender (SV-1725)
is inconformity with the essential requirements as described in Directive 1999/5/EC and satisfies
all the technical regulations to the product within this directive.
EN 300 440-1/-2 / EN 301 489-1/-3 / EN 300 220-1/-2 / EN 60065
Enschede, 21
st
of April 2008
Paul J. Bennett
As Managing Director of Universal Electronics BV
0678
2
RECEIVER
T
RANSMITTER
SV-1725_300x220_RDN-1071008:Sky_Remote_Eye_Instruct_702870 07-10-2008 16:04 Pagina 2