Filter
Top Products
–
27
–
EN
Quick Use Guide
✄
Please refer to “Basic TV
Connection” on the front page
befor you use this unit.
RF Output Channel
If channel 3 is already occupied for
broadcasting,
1)
Set your TV to channel 4.
2)Insert a pre-recorded tape into this
unit.
3)Press [OUTPUT] on the unit so that
the VCR OUTPUT light is lit.
• If noise appears on the TV screen,
press [VCR/TV] on the remote control.
4)Press [PLAY B] once.
5)After a few seconds, hold [PLAY B]
on the unit for 3 seconds.
• The RF output channel will change
to channel 4 from channel 3 and you
will see a playback picture.
• When a picture does not appear on
the TV screen, repeat step 4).
6)Press [STOP C] to stop playback.
Connections
1
Clock Setup
5
VCR/DVD Switching
3
Installing the Batteries
for the Remote Control
2
Turn on the unit for the
first time
4
2
3
1
CHANNEL
STOP
REV FWD
SKIP HG SKIP
OUTPUT
DVDDISC IN
OPEN/CLOSE
PLAY
STOP/EJECTPLAYREC/OTR
VCR
POWER
F.FWDREW
V
ID
E
O
AU
D
IO
REV
SKIP H
OUTPUT
DVDVCR
POWER
DISPLAY VCR DVD PAUSE
SLOW
VCR/TV
SKIP/CH.
PLAY
STOP
REC/OTR
MENU
SETUP TOP MENU
MODE ZOOM
SUBTITLE
T-SET
ANGLE
ENTER
RETURN
SEARCH
MODE
REPEAT A-B
OPEN/CLOSE
/EJECT
SPEED AUDIO
CLEAR/
C. RESET
123
456
789
0
+10
OUTPUT button
DVD OUTPUT
light
VCR OUTPUT
light
DVD button
VCR button
Press [VCR] on the remote control.
(Verify that the VCR OUTPUT light is lit.)
VCR MODE
Press [DVD] on the remote control.
(Verify that the DVD OUTPUT light is lit.)
DVD MODE
2
2
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
1
1
Turn on the TV and set it
to channel 3.
• If channel 3 is already occupied for broadcasting,
see“RF Output Channel” section.
3
3
CH 01
AUTO SET UP
No
No
Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
•You can select only the channels memo-
rized in this unit by using
[SKIP/CH.
GG
/
KK HH
/
LL
]
(or [CHANNEL
KK
/
LL
]).
• If “AUTO SET UP” appears on the TV
screen again, check the cable connections.
Then, press
[B] once again.
Y
Y
es
es Press [MENU]
to exit.
Do you connect the cable from the cable box or
the satellite box to the unit’s ANT-IN jack?
YES
NO
TV ScreenRemote Control
VCR
VCR
VCR
1
1
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
CLOCK SET
MONTH DAY YEAR
1 0 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 – – – –
HOUR MINUTE AM/PM
– – : – – – –
Select the current month.
Select the current day.
• If the clock is not set, the
CLOCK SET screen
appears when you press
[MENU].In this case, go
to step 2).
VCR
VCR
VCR
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 2 0 0 5
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 MON 2 0 0 5
HOUR MINUTE AM/PM
0 5 : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 MON 2 0 0 5
HOUR MINUTE AM/PM
0 5 : 4 0 – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 MON 2 0 0 5
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
B PM
Select the current year.
Select “AM” or “PM”.
8
8 To exit the CLOCK SET
screen
Select the current hour.
Select the current minute.
2
2
3
3
4
4
5
5
6
6
7
7
Hint
Hint
• Pressing only [OUTPUT] on the front
panel DOES NOT switch the mode of the
remote control.You MUST select the cor-
rect mode on the remote control.
or
POWER
MENU
or
or
or
or
or
or
or
✄
H9805UD_EN/SP.qx3 2005.06.10 15:18 Page 27