Filter
Top Products
17
To Suspend the Timer Recording Standby
Mode
When you want to use the VCR for playback, normal
recording or some other operation before the programmed
timer recording perform, you can temporarily suspend the
timer recording standby mode by pressing the [TIMER (REC)]
(19) so that the [ ] indication on the VCR display
disappears.
However, after you have finished using the VCR, be sure to
reactivate the timer recording standby mode by pressing the
[TIMER (REC)] (19) again otherwise the programmed timer
recording will not be performed.
Procedure of Easy Timer Programming on
OSD (Easy Programming Guide)
Press [GUIDE] (13) or
[PROG GUIDE] (45), and the timer
programming procedure appears on
screen display. Follow the
instructions.
• Press [GUIDE] (13) or
[PROG GUIDE] (45) again to exit
the On Screen Display.
Weekly Timer Recording
In step 2 of 4-Key Programming, select the desired day by
pressing [DATE] (12).
For example, SU (Sunday)
(SU=Sunday, MO=Monday, TU=Tuesday, WE=Wednesday,
TH=Thursday, FR=Friday, SA=Saturday)
(SU=Sunday, MO=Monday, TU=Tuesday, WE=Wednesday,
TH=Thursday, FR=Friday, SA=Saturday)
Daily Timer Recording
In step 2 of 4-Key Programming, select the desired days by
pressing [DATE] (12).
For example, C
Timer Recording from an External Signal
Source
If timer recording is performed by a unit connected to the
Audio/Video input sockets, select the A1 or A2 indicator in
step 3 of 4-Key Programming for the programme position.
Setting other Programmes in Succession
Repeat steps 1-9 of 4-Key Programming.
Programming a Timer Recording of a TV
Programme Until its End
(Tape Speed Auto Change Function)
If the VCR determines that the remaining tape time is
insufficient to record the programme to its end during a timer
recording performed in the SP mode, this function
automatically changes the tape speed to ensure that the
whole programme will be recorded.
The tape speed will change as follows:
PAL system: SP # LP
NTSC system: SP # EP
• This function cannot change the recording speed to the
EP mode for PAL system.
Depending on the remaining tape length, recording may be
performed in the LP (EP) mode from the start. However, if the
remaining tape time is still not sufficient in this case, the
programme cannot be recorded to the end.
The tape length must be set correctly. (See page 11.)
Some tapes may not work correctly.
If the recording speed changes from SP to LP during a timer
recording, some brief picture distortion occurs at that point.
To Activate the Tape Speed Auto Change Function:
Press [SPEED] (20) to select [A].
• Every time you press [SPEED] (20), the indication changes
in the following order:
PAL system: SP # LP # EP # A # SP
NTSC system: SP # EP # A # SP
Daily recording
On Screen
Display
VCR Display
A Monday to Friday
MO-FR
M-F
B Monday to Saturday
MO-SA M-S
C Sunday to Saturday
SU-SA S-S
CANCEL : GUIDE
1. 2. 3. 4.
SET SET SET SET
DATE CH ON OFF
TIME TIME
ssss
ss
ss:ss
ss:ss
EASY PROGRAMMING GUIDE
5. PUSH SPEED SP
6. PUSH TIMER
GUIDE
CATEGORY
CHDATE ON OFF
SP––:–– ––:––
: 1
SU ––
CATEGORY
CHDATE ON OFF
SP––:–– ––:––
: 1
SU-SA ––
CATEGORY
ON OFF
SP––:––
––:––
:
1
CHDATE
29SA A2
CHDATE ON OFF
A2 20:02 21:3029SA
CATEGORY: 1
NV-HV60GL_GN.book 17 ページ ２００３年２月３日 月曜日 午後３時３２分