Filter
Top Products
REMOTE CONTROL OPERATION (FOR MODELS PT-47WX54 AND PT-53WX54 ONLY)
19 z
ENGLISH
Programming The Remote Control
The Universal Remote Control can be programmed to
operate many manufacturers’ components, using the
component function buttons for VCR, DVD, AUX, RCVR,
TV, DTV CABLE or DBS. Follow the procedures for
programming your Remote Control with or without a code
for the component.
Note: Determine the manufacturer of the component and look
in the table for the code.
Programming with a Code
Procedure
1. Confirm that the external component is plugged in and
operating.
2. Turn the component off.
3. Press and together, for at least 5
seconds. After 5 seconds, the illuminated mode
(component) buttons will begin to flash. Release the
ACTION and POWER buttons.
4. Press appropriate component button on the Remote
Control
VCR, DVD (CD), AUX (VCR2 or TAPE),
RCVR, DTV, CABLE or DBS.
The component button
will illuminate steadily and all others will go out.
5. Enter the 3-digit component code using the Remote
Control numeric keypad (0 ~ 9 buttons). The component
button will blink twice.
6. Press the Remote Control to test the
component. If the procedure was successful, the
component will turn on and the component key will blink
twice and then go out.
Note: If the component does not operate with the Remote
Control, repeat steps 3 through 6 using another code
(some brands have multiple codes). If an incorrect code
is entered, or if the procedure takes longer than 30
seconds, the programming will fail.
Programming without a Code
This procedure searches all codes and is called the
“sequence method.”
1. Confirm that the external component is plugged in and
on.
2. Turn the component off.
3. Press and together, for at least 5
seconds. After 5 seconds, the illuminated mode
(component) buttons will begin to flash. Release the
ACTION and POWER buttons.
4. Press appropriate component button on the Remote
Control. The component button will illuminate steadily
and all others will go out.
5. Press the button to set the remote control into
the step and set mode.
6. Point the remote control towards the component.
7. Press VOL (the mode key will blink three times), then
press the Remote Control button to test the
component. Continue this process until the proper code
is found. If the procedure was successful, the component
will turn on.
Note: Each time you press the VOL button, make sure that the
component key blinks twice before pressing the POWER
button.
8. Once the device responds, press to store the
code. The mode (component) button will blink twice.
Note: It may take many attempts before the correct code
is found. If you miss a code, press VOL, then press
the button to test the component.
Component Codes
The Universal Remote Control is capable of operating
many component brands after entering a code. Some
components may not operate because the codes are not
available due to limited memory. The Universal Remote
Control does not control all features found in each model.
Default Modes for Remote Control
Device Operates Default
TV
TV (Panasonic Only) Panasonic TV Code
DTV-STB
DTV (Panasonic Only) Panasonic DTV Code
CABLE
CABLE (Preset)
Panasonic CABLE
Code
DBS
DBS (Preset) Panasonic DBS Code
VCR
VCR (Preset0 Panasonic VCR Codes
DVD/CD
DVD and CD (Preset) Panasonic DVD Codes
AUX
Personal Video Recorders,
Tape and VCR2
Panasonic Personal
Video Recorder Code
RCVR
Audio receiver (Preset) Panasonic RCVR code
ACTION
POWER
POWER
Write the code numbers from tables in this space.
This will serve as a reference if you need to program
your Remote Control.
VCR DVD DVD (CD)
AUX (VCR2) AUX (TAPE) RECEIVER
DTV CABLE DBS
ACTION
POWER
POWER
POWER
ACTION
POWER