Filter
Top Products
SETUP CODES FOR TELEVISION
CÓDIGOS DE PROGRAMACIÓN PARA TELEVISIÓN
CODES DE PROGRAMMATION DU TÉLÉVISEUR
A-Mark 0032
AOC 0032, 0048, 0059, 0214
Admiral 0122, 0492
Adventura 0075
Aiko 0121
Akai 0059
Alaron 0208
Ambassador 0206
America Action 0209
Ampro 0780
Anam 0209
Anam National 0084
Archer 0032
Audiovox 0032, 0121, 0209, 0480, 0652
Baysonic 0209
Belcor 0048
Bell & Howell 0045, 0183
Bradford 0209
Brockwood 0048
Broksonic 0032, 0265, 0492
CXC 0209
Candle 0059, 0075, 0085
Carnivale 0059
Carver 0083
Celebrity 0029
Cineral 0121,0480
Citizen 0059, 0068, 0075, 0085, 0089,
0121, 0309
Clairtone 0214
Concerto 0085
Contec 0209, 0214
Craig 0209
Crosley 0083
Crown 0068, 0209
Curtis Mathes 0045, 0059, 0068, 0076, 0080,
0083, 0085, 0089, 0122, 0174,
0183, 0195, 0480, 0495
Daewoo 0048, 0068, 0121, 0480, 0652,
0653
Daytron 0048
Denon 0174
Dumont 0046, 0048
Dwin 0749,0803
Electroband 0029, 0214
Emerson 0048, 0068, 0183, 0206, 0207,
0208, 0209, 0214, 0265, 0309,
0311, 0492, 0652, 0653
Envision 0059
Fisher 0183, 0188
Fujitsu 0208, 0712
Funai 0200, 0208, 0209
Futuretech 0209
GE 0050, 0076, 0080, 0084, 0122,
109
TROUBLESHOOTING
Red Indicator Light does not
blink when you press a key.
Replace the batteries with two
(2) "AA" alkaline batteries (see
Page 3).
The VOL+,VOL- and MUTE
keys are not functional.
Make sure that the volume con-
trol is locked to a component
that has volume capabilities and is
programmed into the remote
control.
Red Indicator Light blinks when
you press a key,but home enter-
tainment component does not
respond.
Make sure you are aiming the
remote control at your home
entertainment component and
that you are within 15 feet of the
component you are trying to
control.
The remote control does not
control home entertainment
components or commands are
not working properly.
Try all listed codes for the com-
ponent brand being set up. Make
sure all components can be oper-
ated with an infrared remote
control.
CH+,CH- and LAST do not
work for your RCA TV.
Due to an RCA design (1983-
1987),only the original remote
control will operate these func-
tions.
Changing channels does not
work properly.
If original remote control
required pressing ENTER to
change channels,to change chan-
nels,press ENTER on the
remote after entering a channel
number.
Tried Auto Scan and still could
not find a working code.
Try Auto Scan again after clearing
out the component key as fol-
lows: Press and hold SET until
Red Light blinks twice, then
release. Next enter 9-9-2. Then
press and release the component
key to be cleared twice.
NOTE: To clear all set up codes and restore functions to Default,
press SET until red light blinks twice,release SET and enter 9-8-1.
Caution:When this clear feature is performed,please note that all of
your set up codes will be reset to the default codes and you will need
to reprogram components.
PROBLEM: SOLUTION: