Filter
Top Products
VISIT US ON THE WEB
You can find programming instructions
and codes for all of our remote
controls, as well as information about
our other products on our website:
www.uselectronics.com
User’s Guide for the
4-in-1 Cable TV Remote Control
for Pioneer
®
Voyager BD-V1000 & 3000
Use this guide in conjunction with your cable
converter manual
© 2003 US Electronics, LLC
All rights reserved
Part Number USE 18256, version 1.0
05202003
Please plug your television power cord
into a separate wall outlet instead of the
power outlet on the cable box.
Tune your television to channel 2, 3 or 4
as directed by your cable provider.
BEFORE YOU BEGIN
2
3
!
Use only new AA Alkaline batteries
to insure consistent operation
Two AA batteries must be installed before
you can program or operate the remote
control.
1. Remove the battery compartment cover
located on the back of the remote control.
2. Place the batteries in the compartment
in positions matching the picture below.
3. Replace the battery compartment
cover.
INSTALL BATTERIES
IMPORTANT
NOTE
4
KNOW YOUR REMOTE
SELECT
MUTE turns volume on and off
TRANSPORT KEYS
perform
standard functions for video
recording for VCRs and DVD
players and controls VOD
functions in cable mode if the
service is available
REW
PLAY
FF
STOP
PAUSE
REC
The diagram below provides a brief description of each key on your universal remote control.
US Electronics provides these function descriptions as a general guide to allow you to become
more familiar with your remote. Functions may vary between different services. Please refer to
your cable converter manual for descriptions of specific functions.
ENT-VGER
Test the code by trying various functions. If the primary function keys fail to respond
satisfactorily try the next code listed for the manufacturer.
If you have tried all the codes listed for the manufacturer and the device does not
respond, try to program the device using Smart Scan
™
as described in section 5.
Remember to record your device codes in section 11 when you are done.
By default, your Enterprise remote controls cable volume through the Cable Box, and the VCR
and DVD through the Television. To allow volume control through a different device:
To return volume control to the default state:
6
Manual Programming
7
PROGRAMMING VOLUME CONTROL
To manually set up the Enterprise to operate a device, find the manufacturer of the device in
the list of manufacturers’ codes. The codes are logically grouped by device type in section 12.
Then perform the following steps:
Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash.
Press and release the VOLUME UP key, the CBL key will remain on.
Press and release the VOLUME DOWN key. The CBL key will turn off when VOLUME
DOWN is pressed, and will turn on when released.
Press and release the key corresponding to the device you wish to use to control
volume. (TV or AUD) After you release the key, the CBL key will flash three times and
turn off.
3
1
2
8
Master Power Control
The Master Power function allows you to turn off and on two or more devices simultaneously
with a single press of the power button. The following steps describe how to program the
Master Power Control function:
The Smart Scan
™
programming instructions can also be found on the battery cover of the remote
control. Smart Scan
™
will allow you to easily try all the available programming codes for the
selected device and find the best match. If you prefer manual programming or already have the
device codes you may also program the remote manually using the steps in section 6.
Turn on power for the device to be programmed.
Begin the Smart Scan
™
procedure by pressing and holding the associated device key
(AUX, VCR, TV) until all device keys on the remote begin to flash (approximately 3
seconds). Release the power key.
If the device your are attempting to program matches the selected device key (e.g. TV
component with the TV device key) proceed to step 5.
If the device your are attempting to program does not match the selected key (e.g. a
second VCR programmed to the AUX device ), locate the correct prefix code for the
device you wish to program from the table listed below. Press and release the prefix
code.
Press and release the POWER key. The device key will stop flashing and remain on.
Point the remote control at the component.
Press and hold the UP ARROW key until the component turns off. While holding the UP
ARROW key the remote will send a new code approximately once every second. The
device button will blink each time a new code is sent. If you pass the code that turns off
the component, press the DOWN ARROW key to return to the previous code.
When the device turns off, you have found a candidate code. Press the POWER key to
turn device back on. Test various functions using the remote control to determine if this
code will work. If primary functions do not work, make sure the device is still on then
resume Smart Scan
™
by pressing the UP ARROW key to find another device code.
Once you have found a satisfactory code, press SELECT to lock the code. The power of
the device must be on. The device key will then flash three times. Go to section 10 to
recall and record your device codes. When all the codes have been attempted the
device button will flash rapidly.
1
2
3
Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash.
Press and release the VOLUME UP key. The CBL device key will stop flashing and stay
on. Press and release the VOLUME DOWN key, and then press and release the OK key.
After you release the OK key, the CBL device key will flash three times and turn off.
1
2
4
5
Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash.
Press and release the POWER key.
Individually press and release each device key corresponding to the components you
wish to be controlled by Master Power. NOTE: If no keys are pressed in this step, no
change will occur in Master Power programming.
1
2
3
Press and hold the device key to be programmed until all device keys begin to flash
(approximately 3 seconds). Release the key. The selected device key will continue to
flash.
Enter the four digit code for the desired component using the number keys. After
pressing the first digit, the device key should light and remain on. If the programming is
successful. After the last digit is pressed the device key should flash three times and
turn off.
1
2
6
Prefix
0
1
4
5
Device
TV
VCR/DVD/PVR
Audio Receivers
Combo Units
7
The Enterprise remote control is already programmed with the code for your Pioneer
©
Cable
Converter. The following sections will help you program your remote to control your other
entertainment components.
3
4
8
Congratulations!
1
This 4 mode remote control has been pro-
grammed to control your Pioneer cable
converter and can be programmed to con-
trol up to three additional entertainment
components by following these easy
instructions.
The volume and channel controls are set
to control the cable converter. This can be
modified by following the instructions in
sections 7 and 9. This remote has a
master power feature for powering all
components together. See details in
section 9.
5
SMART SCAN™ AUTOMATIC PROGRAMMING
9
Press and release the POWER key. The CBL key will flash three times and turn off.
Manually turn on all devices. Then test the Master Power control by pressing the
POWER key.
4
5
To disable Master Power, repeat the previous steps selecting only one device for Master Power
(any device can be selected). The remote will now control the power ON/OFF of each device
separately.
NOTE: Once Master Power has been programmed for two or more devices, pressing the POWER
key in normal operation will cause the remote to transmit the POWER on/off commands for
those devices selected during Master Power programming,
To override this and transmit a POWER on/off command for a device not included in the Master
Power selection, press the DEVICE key for that device and immediately press the POWER key.