Polycom RMX 4000 Home Theater Server User Manual


  Open as PDF
of 2
 
Modifying the Default IP Service
This section describes the definition of H.323 Network Service. For detailed description
of H.323, SIP and ISDN Network Service definitions, see the RMX Getting Started Guide,
“First Time Installation and Configuration”.
In the Fast Configuration Wizard, select Next to move from one window to another.
1
2
3
4
5
6 In the IP Network Service creation confirmation, click OK.
7
8 Click Save & Close.
9 In the Success Message box confirming successful configuration, click OK.
10 In the Reset Confirmation dialog box, click Yes.
11 In the Please wait for system reset message box, click OK.
System restart may take up to five minutes.
12 Refresh the browser periodically until the Login screen is displayed and Login.
In the Main Screen an MCU State indicator displays the time remaining until the
system start-up is complete.
13 Create a new User with Administrator permissions and delete the default User
(POLYCOM). For system security reasons, only when this step is completed and if
there are no System Errors, the system is fully configured and the green RDY LED
on the CNTL module (on the RMX’s front panel) turns ON.
Connecting to a Conference Directly or via Entry
Queue (EQ)
The RMX is shipped with pre-configured default conferencing entities that can be used
to dial in and start conferences. Default (Transit) Entry Queue ID: 1000, default Meeting
Room IDs: 1001, 1002, 1003, and 1004.
H.323 Participants
H.323 participants dial:
[MCU Prefix in Gatekeeper][Conference or Entry Queue ID/Name]
For example, if the MCU prefix in gatekeeper is 925, you can dial to the default (Transit)
Entry Queue by entering 925 or 9251000 and be routed to Meeting Rooms by entering its
ID (i.e. 1001, 1002, 1003 or 1004). You can connect directly to one of the default Meeting
Rooms, by dialing its number, for example: 9251001.
Alternatively, you can use the Entry Queue or conference name to connect directly to
the conference. For example, if the conference name is Maple_Room, the participant can
dial: 925Maple_Room.
SIP Participants
The dialing string is composed of the conference routing name as registered with the
SIP server and domain name in the format: conference_name@domain_name
For example, if conference routing name is 1001, the string is 1001@polycom.com.
ISDN and PSTN Participants
ISDN and PSTN participants can connect to conferences and Meeting Rooms directly or
via an Entry Queue by dialing one of the numbers (including the country and area code
if needed) assigned to the conference, Meeting Room or Entry Queue. When connecting
to an EQ they are routed to their conference according to the conference ID. For
example, if the assigned dial in number is 4045555, the ISDN/PSTN endpoint dials this
number with the appropriate area code (for example, 678) and country code (001).
Conference Control Using DTMF Codes
On the RMX 4000, IPv4 is the default protocol for setting the Network Service in the
Fast Configuration Wizard.
Change the default service
name if required.
Enter the address to be
used by IP endpoints when
dialing in to the MCU.
Enter the IP address(es) of
the media card(s).
Enter the subnet mask of
the MCU.
Enter the IP address of the
default router.
Enter the name of the MCU
on the network.
Optional. Select Specify to
define a DNS server.
Optional. Define the DNS
server properties:
• Registration mode
• The name of the MCU
domain
• The static IP address of
the primary DNS server
Select H.323 as the IP
Network Type.
Select Specify to configure
the gatekeeper parameters.
Enter gatekeeper’s host
name or IP address.
Enter the string with which the
MCU registers itself with the
gatekeeper.
Enter the alias that identifies
the RMX’s Signaling Host
within the network. Up to five
aliases can be defined for
each RMX.
Optional. Modify the default
settings of the system flags
that define the general
system behavior such as the
number of digits in the
conference ID assigned by
the MCU.
These flags can be modified
later, if required, by selecting
the System Configuration
option from the Setup menu.
Operation DTMF String Operation DTMF String
Mute My Line *6 Request individual
assistance
*0
Unmute My Line #6 Request assistance for
conference
00
Increase Broadcast Volume *9 Increase Listening Volume *76
Decrease Broadcast Volume #9 Decrease Listening Volume #76
Play Help Menu *83 Change To Chairperson *78
Start Click&View to modify
personal layout
** Show Number of
Participants
*88
RMX™ 4000
2
DOC2521A
 previous