Filter
Top Products
English - 9
Plug & Play (Initial Setup)
When you turn the TV on for the first time, a sequence of on-screen prompts will assist in configuring basic settings. To turn on
the TV, press the POWER
P
button.
✎
Plug & Play is available only when the Source is set to TV.
✎
To return to the previous step in the Plug & Play sequence, select Previous, and then press ENTER
E
.
✎
Before turning on the TV, make you have connected the TV to an antenna or cable connection (p. 8).
1
Selecting the OSD
Language
Press the ▲ or ▼ button to select a language. Press ENTER
E
twice
when done.
2
Setting up the Network
Set up your network connection. Press the ENTER
E
button to start. If
you do not know your network set up information or want to set to it later,
select Skip. We suggest you skip network connection setup now and
refer to “Wired/Wireless Network Connection” in the e-Manual for set up
requirements and instructions, and the Network Connection section of this
manual (Page 15). You can set up the network connection later using the
Network menu.
3
Selecting the usage
mode
Press the ▲ or ▼ button to select Home Use, and then press the ENTER
E
button twice.
Select the Home Use mode. Store Demo mode is for retail environments.
4
Setting the Clock
Mode
Press the ▲ or ▼ button to select Auto or Manual, and then press ENTER
E
twice.
✎
If you selected Auto, you’ll go to the Time Zone and DST screen. Select Time
Zone or DST, and then press ENTER
E
. On the Time Zone screen, use the ▲ or ▼
button to select your zone, and then press ENTER
E
. On the DST screen, press,
ENTER
E
, then select whether to turn DST (Daylight Savings Time) on or off. When
done, press ENTER
E
.
✎
If you selected Manual, you’ll go to the Date and Time screen. Select Date or Time,
and then press ENTER
E
. Then, use the number buttons or the ▲ or ▼ button to
set the date or time. Use the ◄ or ► button to move between entry fields. When
done setting the Date and Time, select Next, and then press ENTER
E
.
5
Selecting search
options for auto tuning
Press the ▲ or ▼ button to select Air or Cable, and then press ENTER
E
. A check
appears on your selection. Select Next, and then press the ENTER
E
button. You can
check both if you have both connected.
✎
If you selected Cable, you’ll go to the Cable System screen. Use the ▲ or ▼
button to select Digital or Analog, and then press. ENTER
E
. Use the ▲ or ▼
button to select the correct cable signal format - STD, HRC, or IRC - and then press
ENTER
E
. Most cable systems use STD. Select the correct cable signal format for
both the Digital and Analog systems.
✎
When done, select Next, and the press ENTER
E
.
6
Selecting and
memorizing channels
The channel search will start automatically. This can take up to 30 minutes.
For more information, refer to Channel → Auto Program in the e-Manual.
✎
Press the ENTER
E
button at any time to interrupt the memorization process.
7
Enjoy your TV. If you want to watch a broadcast program, select Close.
If you want to enjoy Smart Hub, select Smart Hub. Smart Hub will start. For more detailed
information, refer to “Smart Hub” in the e-Manual.
If You Want to Rerun Plug & Play...
O
MENU → System → Plug & Play → ENTER
E
✎
NOTE
y To change the TV’s setting from Store Demo to Home Use when not in Plug & Play, press the volume button on the TV.
When you see the volume bar on the screen, press and hold the MENU button on the TV for 5 sec.
P
POWER
INFO
GUIDE
[UD6000(6050)-ZA]BN68-03330A-02Eng.indb 9 2011-02-21 오후 3:44:06