Filter
Top Products
Quick Guide
Your New Wide TVOperation
Special Features
Front Panel LED Indicators
Remote Control
You can use the remote control up to about 23 feet from the TV. When using the remote control, always point it directly at the TV. You can also
use your remote control to operate your Set-Top Box, VCR, Cable box or DVD player.
1. POWER
Turns the TV on and off.
2. S.MODE
Adjust the TV sound by selecting one of
the preset factory settings. (or select your
personal, customized sound settings.)
3. P.MODE
Adjust the TV picture by selecting one of
the preset factory settings. (or select your
personal, customized picture settings.)
4. +100
Press to select cable channels over 100
on TV.
5. VOL
+
, VOL
-
Press to increase or decrease the volume.
6. MUTE
Press to mute the TV sound.
7. Anynet
Runs the Anynet view functions and sets
up the Anynet devices.
8. MENU
Displays the main on-screen menu.
9. STILL
Press to stop the action during a
particular scene. Press again to resume
normal video.
10. P.SIZE
Press to change the picture size.
11. MODE
Selects a target device to be controlled
by the Samsung remote control (i.e., TV,
STB, VCR, CABLE, or DVD).
12. PRE-CH
Tunes to the previous channel.
13. SOURCE
Press to display all of the available video
sources (i.e., TV, Set-Top Box, VCR, DVD,
DTV, PC).
14. CH , CH
Press to change channels.
15. INFO
Press to display information on the TV
screen.
16. EXIT
Press to exit the menu.
17.
……
,
††
,
œœ
,
√√
, ENTER
Press to select highlight up, down, left, or
right. While using the on-screen menus,
press the ENTER to activate (or change) a
particular item.
18. MTS (MULTICHANNEL TELEVISION
STEREO)
Press to choose Stereo, Mono or SAP
(Secondary Audio Program).
19. SRS
Activates TruSurround.
20. ADD/DEL
Press to add or erase channels in the TV’s
memory.
Use the ADD/DEL button to memorize
and erase the fine tuning after fine tuning
channels.
21. SLEEP
Press to select a preset time interval for
automatic shutoff.
22. PIP (Picture In Picture)
Activates PIP.
23. Fav.CH (Favorite Channel)
Press to switch between your favorite
channels.
24. SET
Used during set up of this remote control,
so that it will work compatibly with other
devices (Set-Top Box, VCR, Cable box,
DVD, etc.).
25. DNIe (Digital Natural Image
engine)
Activates DNIe.
26. PIP Controls
SWAP; Press to exchange the video
signal that is currently displayed on the
main screen with the signal in the PIP
window.
CH / ; Press to display the
available channels in sequence.
(These buttons change channels in the
PIP window only.)
27. VCR/DVD Controls
Controls VCR or DVD functions: Rewind,
Stop, Play/Pause, Fast Forward.
28. RESET
If your remote control is not functioning
properly, take out the batteries and press
the reset button for about 2~3 seconds.
Re-insert the batteries and try using the
remote control again.
Storing Channels in Memory (Automatic Method)
First, select the correct signal source (“Air”, “STD”, “HRC” or “IRC”)
as described before.
Press the MENU button.
Press the … or † button to select
“Channel”, then press the ENTER
button.
Press the … or † button to select “Auto
Program”, then press the ENTER button.
Press the ENTER button to start the auto
program.
The TV begins memorizing all of the
available stations.
Press the ENTER button at any time to
interrupt the memorization process.
Press the EXIT button to exit.
Selecting the Video Signal Source
Before your TV can begin memorizing the available channels,
you must specify the type of signal source that is connected to the TV
(i.e., an antenna or a cable system).
Press the MENU button.
Press the … or † button to select
“Channel”, then press the ENTER
button.
Press the … or † button to select
“Air/CATV”, then press the ENTER
button.
If you are connected to an antenna,
press the … or † button to select “Air”.
If you connected cable, press the … or
† button to select the type of cable
system: “STD”, “HRC” or “IRC”.
Press the EXIT button to exit.
Channel
Antenna : Ant.1 √
Air/CATV : Air √
Auto Program √
Add/Delete √
Favorite Channels √
Name √
Fine Tune √
▼ More
Move Enter
Return
Channel
Setup
Sound
Picture
Input
Start
Auto Program
Enter Return
Stop
Auto Program
Enter Return
Air 11
Channel
Antenna : Ant.1 √
Air/CATV : Air √
Auto Program √
Add/Delete √
Favorite Channels √
Name √
Fine Tune √
▼ More
Move Enter
Return
Channel
Setup
Sound
Picture
Input
Channel
Antenna : Ant.1
Air/CATV : Air
Auto Program
Add/Delete
Favorite Channels
Name
Fine Tune
▼ More
Move Enter Return
Channel
Setup
Sound
Picture
Input
Air
STD
HRC
IRC
Customizing Your Remote Control
Your TV comes equipped with a universal remote control. In addition to controlling the TV, the universal remote control
can also operate a VCR, Cable box, DVD and Set-Top Box made by Samsung (even if your VCR, Cable box and DVD
are made by manufacturers other than Samsung).
NOTE : The remote control might not be compatible with all VCRs, DVD players and Cable boxes.
Setting Up Your Remote Control to Operate Your VCR (Cable box or DVD player)
Turn off your VCR (Cable box or DVD player).
Press the MODE button to switch the remote control to the VCR (CABLE or DVD) mode.
The remote control has five modes: TV, STB, VCR, CABLE and DVD.
On your Samsung remote control, press the SET button.
Enter 3 digits of the VCR (Cable box or DVD player) code listed on next page for your brand of VCR (Cable box or
DVD player).
Make sure you enter 3 digits of the code, even if the first digit is a “0”. (If more than one code listed, try the first one.)
Press the POWER button. Your VCR (Cable box or DVD player) should turn on. If your VCR (Cable box or DVD player)
turns on, your remote control is now set correctly.
If your VCR (Cable box or DVD player) does not turn on, repeat steps 2, 3, and 4, but try one of the other codes listed
for the brand of your particular VCR (Cable box or DVD player).
Once your remote control is set up, press the MODE button any time you want to use the remote to operate your VCR
(Cable box or DVD player).
NOTES
• When your remote is in the TV mode, the VCR (or DVD player) control buttons (REW, STOP, PLAY/PAUSE and FF)
will still operate your VCR (or DVD player).
• When your remote control is in the STB, VCR, CABLE or DVD mode, the volume buttons still control your TV’s
volume.
BP68-00426A-00
The three lights on the front panel indicate the status of your TV.
Indicator Light Key
: Light is On
: Light is Blinking
: Light is Off
• It takes about 30 seconds for the TV to warm up, so normal brightness may not appear immediately.
• The TV has a fan to keep the inside lamp from overheating. You’ll occasionally hear it working.
TIMER
Standby state.
The picture will automatically appear in about 15 seconds.
Auto Timer ON/OFF has been set and the set will automatically be turned on in about 25 seconds.
A cooling fan inside the set is not operating normally.
Lamp cover on rear of the set is not properly shut.
Check if the ventilation hole on the rear of the set is blocked, because if the inner temperature is too
high, the power will shut off.
Lamp may be defective. Please contact a certified technician.
LAMP STAND BY/TEMP Indication
BP68-00426A-00_QG_0831 9/3/04 3:11 PM Page 2