Filter
Top Products
51
Dimension: 140mm x 215mm
Operation of Remote Control (Continued)
L HOW TO IDENTIFY A CABLE CONVERTER
L To Identify Your Cable Converter –Direct
Entry Method.
Use the following steps and list to quickly find
the remote control code for your cable TV
converter.
• First look up your converter’s remote code
number before going through the direct code
entry steps below.
• If this procedure does not identify your
converter, use the Search method for
identification.
(1)Press
CATV/DVD
button.
(2)Press and hold down
DISPLAY
and
CH DOWN
(
9
)
on your remote control.
Then release both buttons.
(3)Within ten seconds after releasing
DISPLAY
and
CH DOWN (
9
)
, enter your converter’s two-
digit code number using
REMOTE KEYPAD
(refer to list).
• The remote control is now ready to send
commands to your converter.
• Some brands have more than one remote code
listed due to changes in the remote codes from
early to later model years. In such cases, you
may have to try more than one code to find the
code your converter accepts.
Note:
Depending on the model, year produced, brand,
and type of CATV converter, some models may
not be compatible with the remote control.
L To Identify Your Cable Converter – Search
Method.
(1)Press
CATV/DVD
button.
(2)Press the POWER button on the cable
converter to ON.
(3)Stand at least six feet away from the converter.
Point the remote towards the converter.
Hold down the
DISPLAY
and
CH UP (
8
)
at the
same time. KEEP HOLDING THE BUTTONS
DOWN.
(4)Watch the Channel Number indicator on the
converter.
Channel numbers will scan up when the
converter has been identified.
Release the
DISPLAY
and
CH UP (
8
)
as soon
as the channel numbers start to scan up.
The converter’s remote control code number
has been identified, and the remote is ready to
operate the converter.
TIPS ON IDENTIFYING YOUR CABLE
CONVERTER:
Be Patient: a minute or two can seem a lot
longer when you’re waiting for something to
happen, but the code should be identified within
2 minutes. Remember, it is only a one-time set-
up.
Be careful not to let the CATV converter scan
more than five channels when the indicator
starts to move up. If you continue holding down
the
DISPLAY
and
CH UP (
8
)
after five channel
scans, the proper remote code can be passed
up, and the two minute identify cycle will have
to be repeated.
If a channel change does not occur on the cable
converter within two minutes, read the
identifying instructions again and repeat the
steps. Should a channel change still not occur,
the remote will not operate with the desired
converter.
Note:
Some satellite receivers can be operated by the
REMOTE CONTROL. If you have a Satellite
Receiver, you can use the above method to
search for available channels.
CATV CONVERTER REMOTE CONTROL
BRAND CODE NUMBER
Anvision 07, 08
Cable Star 07, 08
Eagle 08
General Instrument 04, 05, 15, 23, 24, 25,
30, 36
Jerrold 04, 05, 15, 23, 24, 25,
30, 36
Magnavox 07, 08, 19, 25, 28, 29,
32, 33, 40, 41
Oak Sigma 18
Panasonic 27, 39
Philips 07, 08, 19, 26, 28, 29,
32, 33, 40, 41
Pioneer 18, 20
Randtek 07, 08
RCA 27, 43
Scientific Atlanta 03, 22, 42
Sony 44
Viewstar 07, 08, 19, 26, 28, 29,
32, 33, 40, 41
Zenith 14
20F630[51-56].p65 25/3/03, 3:07 PM51