Filter
Top Products
57
Settings and Adjustments
Setting the Digital Output Signal
Switches the methods of outputting audio signals when
you, connect 1. a digital component such as a receiver
(amplifier) having a digital connector, 2. an audio
component having a built-in decoder (Dolby Digital or
DTS), 3. a DAT or MD via the DIGITAL OUT OPTICAL or
COAXIAL connector using an optical or coaxial digital
connecting cord. For connection details, see pages 10 and
12.
When you select “ON,” set “DOLBY DIGITAL” and
“DTS.”
x DOLBY DIGITAL
Selects the Dolby Digital signals to be output via the
DIGITAL OUT OPTICAL and COAXIAL connectors. You
cannot select this item when you set “DIGITAL OUT” to
“OFF.”
•
D-PCM (Downmix PCM): when the player is connected
to an audio component lacking a built-in Dolby Digital
decoder. If you play Dolby Digital sound tracks, the
output audio signals are mixed down to 2 channels.
You can select whether the signals conform to Dolby
Surround (Pro Logic) or not by making adjustments to
the “DOWNMIX” item in “AUDIO SETUP.”
• DOLBY DIGITAL: when the player is connected to an
audio component with a built-in Dolby Digital decoder.
If the player is connected to an audio component
lacking a built-in Dolby Digital decoder, do not set this.
Otherwise, when you play the Dolby Digital sound
track, a loud noise or no sound will come out from the
speakers, affecting your ears or causing the speakers to
be damaged.
Note
When you select “D-PCM,” set Virtual Enhanced Surround (VES)
to “OFF.” Otherwise, the player will not output signals from the
DIGITAL OUT OPTICAL or COAXIAL connector.
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
DOWNMIX:
DIGITAL OUT:
DOLBY DIGITAL:
To set, press , then .
To quit, press .
OFF
STANDARD
DOLBY SURROUND
ON
D-PCM
DTS:
OFF
ENTER
DISPLAY
x DOWNMIX
Switches the mixing down methods when you play a
DVD on which rear signal components such as LS, RS or S
are recorded in Dolby Digital format. For details on the
rear signal components, see “Displaying the audio
information of the disc” (page 35).
The “DOWNMIX” setting affects the following
connectors:
– AUDIO OUT connectors
– DIGITAL OUT OPTICAL and COAXIAL connectors
(when you set “DOLBY DIGITAL” to “D-PCM” in
“AUDIO SETUP” in the setup display)
•
DOLBY SURROUND: when the player is connected to
an audio component that conforms to Dolby Surround
(Pro Logic). The output signals which reproduce the
Dolby Surround (Pro Logic) effect are mixed down to 2
channels.
• NORMAL: when the player is connected to an audio
component that does not conform to Dolby Surround
(Pro Logic). The signals without the Dolby Surround
(Pro Logic) effect are output.
x DIGITAL OUT
Selects output signals via the DIGITAL OUT OPTICAL
and COAXIAL connectors.
•
ON: Normally select this position. When you select
“ON,” set “DOLBY DIGITAL” and “DTS.” For details
on setting these items, see “Setting the Digital Output
Signal.”
• OFF: when the player does not output the sound signals
via the DIGITAL OUT OPTICAL and COAXIAL
connectors, the influence of the digital circuit upon the
analog circuit is at a minimum.
Notes
• When you play sound tracks with a 96 kHz sampling
frequency, the output signals from the DIGITAL OUT
(OPTICAL, COAXIAL) connectors are converted to 48 kHz
(sampling frequency). The analog audio signals from the
AUDIO OUT connectors are not affected by this setting and
keep their original sampling frequency level.
• When you select “OFF,” you cannot set “DOLBY DIGITAL”
and “DTS.”