Filter
Top Products
57
FAQs, etc.
Technical Information
1
678
3
9
45
10
1514131211
2
* Mark: Applicable input signal for Component (Y, PB, PR), HDMI and PC
Input signal that can be displayed
horizontal frequency (kHz) vertical frequency (Hz) COMPONENT HDMI PC
525 (480) / 60i 15.73 59.94
**
525 (480) /60p 31.47 59.94
**
750 (720) /60p 45.00 59.94
**
1,125 (1,080) /60i 33.75 59.94
**
1,125 (1,080) /60p 67.43 59.94
*
1,125 (1,080) /60p 67.50 60.00
*
640 × 400 @70 31.47 70.08
*
640 × 480 @60 31.47 59.94
*
Macintosh13” (640 × 480) 35.00 66.67
*
640 × 480 @75 37.50 75.00
*
852 × 480 @60 31.47 59.94
*
800 × 600 @60 37.88 60.32
*
800 × 600 @75 46.88 75.00
*
800 × 600 @85 53.67 85.08
*
Macintosh16” (832 × 624) 49.73 74.55
*
1,024 × 768 @60 48.36 60.00
*
1,024 × 768 @70 56.48 70.07
*
1,024 × 768 @75 60.02 75.03
*
1,024 × 768 @85 68.68 85.00
*
Macintosh 21” (1,152 × 870) 68.68 75.06
*
1,280 × 1,024 @60 63.98 60.02
*
1,366 × 768 @60 48.36 60.00
*
Note
•
Signals other than above may not be displayed properly.
•
The above signals are reformatted for optimal viewing on your display.
PC Input Terminals Connection
Pin No.
Signal Name
Pin No.
Signal Name
Pin No.
Signal Name
R
6
GND (Ground)
11
NC (not connected)
G
7
GND (Ground)
12
NC
B
8
GND (Ground)
13
HD/SYNC
NC (not connected)
9
NC (not connected)
14
VD
5
GND (Ground)
10
GND (Ground)
15
NC
•
Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical
scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200
lines.)
•
Some PC models cannot be connected to the set.
•
There is no need to use an adapter for computers with IBM PC/AT compatible D-sub 15P terminal.
•
The maximum resolution: 1,280 × 1,024
If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity.
•
Signal Names for D-sub 15P Connector
Pin Layout for PC Input Terminal
Side Bar
Do not display a picture in 4:3 mode for an extended period, as this can cause “Image
retention” to remain on either or both sides of the display field.
To reduce the risk of such “
Image retention”
, change the brightness of the side bars.
•
The side bar may flash (alternate black/white) depending on the picture. Using
Studio ref mode will reduce such flashing (See p. 56).
Side Bar
4:3
Screen
Display
Image retention
Split - Screen
•
TV screen (RF input) cannot be displayed in both main and split frame simultaneously.
•
The Split-screen feature is not available when using PC and SD Card viewing mode as a source. HDMI input
cannot be displayed in Split frame.