Symphonic STL1504 Flat Panel Television User Manual


  Open as PDF
of 4
 
You may view specially labeled (cc) TV pro-
grams, movies, news and prerecorded tapes,
etc. with either a dialogue caption or text dis-
play added to the program.
1) Press the MENU button so that the menu
display appears on the TV screen.
2) Press the CH(annel) ▼ or ▲ button to point
to "CAPTION".
3) Press the VOL(ume)
n
or
m
button to
select the mode you wish.
4) When done, press the MENU button to exit
the menu.
PICTURE ADJUSTMENT
BACK LIGHT SELECTION
1) Press the MENU button so that the menu display appears on the TV screen.
2) Press the CH(annel) ▼ or ▲ button to point to "BACK LIGHT".
3) Press the VOL(ume)
n
or
m
button to select the mode you wish.
4) When done, press the MENU button to exit the menu.
LANGUAGE SELECTION
If you want to change the language of the on-screen menu,
follow the procedure below.
1) Connect the power cord to a standard AC outlet.
Note: If some digits appear in the corner of the screen,
press the POWER button without unplugging the power cord.
2) Press the POWER button to turn on the TV.
3) Press the MENU button so that the menu display appears
on the TV screen.
4) Press the CH(annel) ▼ or ▲ button to point to "LANGUAGE".
5) Select [ENGLISH], [ESPAÑOL] or [FRANÇAIS]
by using the VOL(ume)
n
or
m
button.
6) Press the MENU button to exit the menu.
CHANNEL PRESETTING
To preset a channel or to change a preset channel, follow the procedure below.
1) Press the POWER button to turn on the TV.
2) Press the MENU button so that the menu display appears on the TV
screen.
3) Press the CH(annel)
▼ or ▲ button to point to "CHANNEL SET UP".
Then press the VOL(ume)
m
button.
4) Press the CH(annel) ▼ or ▲ button to point to "AUTO PRESET CH".
Then press the VOL(ume)
m
button.
The tuner scans and memorizes all active channels in your area.
● The TV distinguishes between standard TV channels and cable (CATV)
channels.
● When AUTO PRESET CH action is completed, the lowest memorized
channel reappears on the screen. When there is no signal to ANT in jack,
"NO TV SIGNALS" will appears. In this case, please check the antenna connections, then try
again the auto preset channel.
● When you press the CH(annel) ▼ or ▲ button after selecting AUTO PRESET CH,
the tuner will stop at the memorized channels only.
● The TV may memorize TV channels as CATV channels if the reception conditions are poor. If
this happens, try the AUTO PRESET CH action again when reception conditions are better.
[ADD/DELETE FUNCTION]
1) Press the MENU button so that the menu display appears on the TV screen.
2) Press the CH(annel)
▼ or ▲ button to point to "CHANNEL SET UP".
Then press the VOL(ume)
m
button.
3) Press the VOL(ume)
m
button so that "ADD/DELETE CH" is selected.
4) Use the CH(annel) ▼ or ▲ button to select the channel you wish to put
into memory or to erase from memory.
Perform "ADD/DELETE CH" function while this display appears on the
screen.
●
Press the VOL(ume)
m
button to light up the channel number
in LIGHT BLUE if you wish to add the channel into memory.
●
Press the VOL(ume)
m
button to light up the channel number
in LIGHT RED if you wish to erase the channel from memory.
5) Press the MENU button to exit the menu.
MTS (Multi-Channel Television Sound) SYSTEM
You can listen to a program in MTS stereo by following the steps below.
[To Select STEREO, MONO or SAP in Stereo broadcast]
1) Press the MENU button so that the menu display appears on the TV screen.
2) Press the CH(annel) ▼ or ▲ button to point to "TV SOUND".
3) Press the VOL(ume)
n
or
m
button to select your desired stereo mode.
([MAIN], [MONO] or [SAP])
PREPARATION FOR USE
WATCHING A TV PROGRAM
1) Press the POWER button to turn on the TV.
2) Select the desired channel with the CH(annel) ▼ or ▲ button.
3) Adjust the volume to the desired listening level using the VOL(ume)
n
or
m
button.
4) Adjust picture controls for a natural looking image. (See "PICTURE ADJUSTMENT".)
SETTING THE SLEEP TIMER
The sleep timer function allows you to have the POWER automatically turn
off after a set time period.
1) Press the POWER button to turn on the TV and press the SLEEP button
on the remote control .
2) You may change the sleep time by pressing the SLEEP
button on the remote control repeatedly. The timer can be set up to 90
minutes. 10 minutes each time the SLEEP button is
pressed. (The timer display counts up and sleep timer
will be displayed on the screen when you press the
SLEEP button on remote control.)
Note: When you disconnect the unit from the AC outlet or when you have a power failure, the
sleep time will be lost.
CLOSED CAPTION SELECTION
SLEEP 10 MINUTE
To cancel the sleep timer:
Press the SLEEP button repeated-
ly until "SLEEP 0 MINUTE" is
displayed.
: Press the VOL(ume)
n
or
m
button.
- TV SET UP -
PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TV SOUND [MAIN]
BACK LIGHT [BRIGHT]
- CHANNEL SET UP -
ADD/DELETE CH (TV)
AUTO PRESET CH
- CHANNEL SET UP -
ADD/DELETE CH (TV)
AUTO PRESET CH
- TV SET UP -
PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TV SOUND [MAIN]
BACK LIGHT [BRIGHT]
- TV SET UP -
PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TV SOUND [MAIN]
BACK LIGHT [BRIGHT]
- TV SET UP -
PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TV SOUND [MAIN]
BACK LIGHT [BRIGHT]
To show the status, press the
DISPLAY button on the remote
control.
SAP: Second Audio Program,
which means your program, can
also be received in a second lan-
guage or sometimes a radio station.
- TV SET UP -
PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TV SOUND [MAIN]
BACK LIGHT [BRIGHT]
- TV SET UP -
PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [
CAPTION1
]
TV SOUND [MAIN]
BACK LIGHT [BRIGHT]
- TV SET UP -
PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [
CAPTION2
]
TV SOUND [MAIN]
BACK LIGHT [BRIGHT]
- TV SET UP -
PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [TEXT1]
TV SOUND [MAIN]
BACK LIGHT [BRIGHT]
- TV SET UP -
PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [TEXT2]
TV SOUND [MAIN]
BACK LIGHT [BRIGHT]
Type of
broadcast
Regular
-None-
ST EREO
SAP
Menu
Selection
MAIN
MONO
SAP
-None- -None-
MONO
ST EREO
SAP
MAIN
MAIN
Stereo
broadcast
: Press the VOL(ume)
n
or
m
button.
BRIGHTNESS
CONTRAST
COLOR
TINT
SHARPNESS
VOL(ume)
VOL(ume)
to decrease
brightness
to increase
brightness
to decrease
contrast
to increase
contrast
to pale to brilliant
to purple to green
to soft to clear
-
BRIGHTNESS
+ -
CONTRAST
+ -
COLOR
+ -
TINT
+ -
SHARPNESS
+
1) Press the MENU button so that the menu
display appears on the TV screen.
2) Press the CH(annel)
▼ or ▲ button to
point “PICTURE”. Then press the
VOL(ume)
m
button.
3) Select the feature you wish to adjust with
the CH(annel) ▼ or ▲ button and adjust it
with the VOL(ume)
n
or
m
button.
OPERATIONS
: Press the CH(annel) ▼ or ▲ button.
- TV SET UP -
PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TV SOUND [MAIN]
BACK LIGHT [BRIGHT]
- TV SET UP -
PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TV SOUND [MAIN]
BACK LIGHT [NORMAL]
- TV SET UP -
PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TV SOUND [MAIN]
BACK LIGHT [DARK]
: Press the VOL(ume)
n
or
m
button.
- TV SET UP -
PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TV SOUND [MAIN]
BACK LIGHT [BRIGHT]
- TV SET UP -
PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TV SOUND [MONO]
BACK LIGHT [BRIGHT]
- TV SET UP -
PICTURE
CHANNEL SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
TV SOUND [SAP]
BACK LIGHT [BRIGHT]
Note:
●
In the above steps, the picture adjustment display will disappear from the TV screen automati-
cally after about 10 seconds if you do not press any buttons. Press the MENU and VOL(ume)
m
button so that "PICTURE" is selected. Then press the CH(annel) ▼ or ▲ button repeatedly
until the display returns to the screen.
 previous