Technicolor - Thomson VT2020G VCR User Manual


 
22
In our efforts to improve the quality of our products, we reserve the right to change their features. The information
contained in these instructions are therefore liable to change and are not contractual.
T8003MER-T8124 MER-T8015MER-T8044MER-T8424MER-T8444MER-R8042MER-R8423MER/GB-D/MR-BEI/910
Mains supply 200 to 240 V ±10% - 50/60 Hz
Consumed power (*) 16 W when ON - 4 W in the eco mode
Clock autonomy approx.30 minutes
Dimensions (W/H/D) 393 x 94 x 278 mm
Weight approx.4.0 kg
Functioning conditions +5°C to +40°C - Surrounding humidity:80 % maximum
Tape heads (*) video: 2 - 4 rotary heads
audio: 1 fixed head (mono linear track)
Tuner PLL,VPS/PDC Type
Reception band I-III-IV Hertzian (aerial)
Inter-band (cable network)
Hyper-band (cable network)
Frequency ranges 45 to 855,25 MHz
Colour system (*) PAL - SECAM - MESECAM
Playing of an NTSC tape on TV PAL 60Hz
Reception norms (*) LL’ - BG - DKK’
Number of storable channels 99
Modulator (*) UHF
Channel 21 to 69 - Pre-set at the factory on channel 60
Standards L - G - K
Remote control Infrared 33 Khz - Batteries 2 x 1,5 V (AA)
Menu language (*) French - English - German - Italian - Spanish - Swedish - Danish - Dutch - Polish
Czech - Hungarian - Russian
Automatic functions On (using any key)
Play (with protected tape)
Rewinding (at the end of the tape)
Tapes VHS format - Rewinding time:130s with E 180
If you have any problems, check the counter measure for each symptoms listed below. If the problem persists,note your VCR
Model Number and Serial Number which can be found on the back of your VCR. Contact your nearest authorized service
centre or dealer for assistance.
VCR set cannot be turned on. 1. Make sure the power cord plug is inserted in an AC power outlet.
2. Ensure the Power On/Off switch is on.
Intermittent or no remote operation. 1.Aim the remote control directly at the VCR. Nothing should be blocking the
remote control and the VCR.
2. Use new batteries.The batteries in the remote control may be weak or dead.
Snowy picture.
Noisy sound.
1. Check your aerial or cable VCR connection.
2. Check the antenna connection on the VCR and on the wall.
Dotted lines or stripes Spotted picture
(crosstalk.) Lines or streaks in picture
(interference).
1.This may be caused by local interference (e.g. cars,neon signs, hair dryers, personal
computer, audio devices,handphone, radio stations, etc.).Try moving the interfering
equipment or adjust the aerial antenna.
Double images or“ghosts”. 1.A highly directional antenna may improve the Picture.This may be caused by
reflections from nearby mountains or building.
Good picture.
Noisy sound.
1. Check the transmission standard selected for the current VCR programme.
MESECAM 1. If the pictures are poor,check that the MESECAM function is off.
No picture.
No.sound.
1. Ensure the power On/Off switch is on.
2. Check the antenna connection.
Recording is impossible: 1. See if the safety tab of the cassette isn’t broken.
2. Check if you have properly performed the steps for the preparation of your
recording as set out on page 13.
Technical features
Identifying and correcting problems
(*):
If included
(*)
T/R8---MER/GB/D/MR-BEI/910 4/01/00 11:31 Page 22