Filter
Top Products
1918
Preparations
■ Removing the connection terminal cover
Press on the circle (“O”) while
sliding the cover in the direction of
the arrow. The cover will come off.
USB
COMPUTER
(
Y,P
B
/P
R
)
S-VIDEOVIDEO
VIDEO
R - AUDIO - L
AUDIO
MONITOR
CONTROL
12
USB
COMPUTER
(
Y/P
B
/P
R
)
S-VIDEOVIDEO
VIDEO
R - AUDIO - L
AUDIO
MONITOR
CONTROL
12
(1)
(8) (7)(9) (6)
(2)(3)(4)
(5)
(1) COMPUTER 2 terminal
Input RGB signal from a computer or other source, or a component video signal (Y/P
B/
P
R) from video equipment.
(2) COMPUTER 1 terminal
Input RGB signal from a computer or other source, or a component video signal (Y/P
B/
P
R) from video equipment.
(3) MONITOR terminal
Connect to a computer display, etc.
(4) USB terminal
Connect to a computer’s USB terminal when using the remote-control mouse function.
p.52
(5) S-VIDEO terminal
Input S video signals from video equipment.
(6) VIDEO terminal
Input video signals from video equipment.
(7) AUDIO (L/R) terminal
Input audio signals from video equipment.
(8) AUDIO terminal
Input audio signals from a computer or video equipment with a component video signal
output terminal.
(9) CONTROL terminal
When operating the projector via a computer, connect this to the controlling computer’s
RS-232C port.
p.71
Note
• Although this owner’s manual abbreviates component video signals as Y/PB/PR, the
product also supports signals from video equipment marked “Y/C
B/CR.”
■ Loading dry-cell batteries
into the remote control
q Remove the battery cover.
w Insert the dry-cell batteries.
Be sure to align the plus and minus
ends of the batteries properly.
Two batteries (LR03 (SIZE AAA)) are
used.
e Replace the battery cover.
(2)
(1)
■
Operating the remote control
Point the remote control toward the
projector’s infrared remote sensor,
and press a button on the remote
control.
• Operating the projector from the front
• Operating the projector from the rear
Dry-cell batteries
• Remove batteries from remote control when not using for extended periods.
• If the remote control stops working, or if its range decreases, replace all the batteries
with new ones.
The remote control
• The remote control may fail to operate if the infrared remote sensor is exposed to bright
sunlight or fluorescent lighting.
• Do not drop or bang.
• Do not leave in hot or humid locations.
• Do not get wet or place on top of wet objects.
• Do not take apart.
• In rare cases, ambient conditions could impede the operation of the remote control. If
this happens, point the remote control at the main unit again, and repeat the operation.
Names of the connection terminals Preparing and using the remote control
O
N
/
S
T
A
N
D
B
Y
I
N
P
U
T
M
E
N
U
A
U
T
O
S
E
T
F
A
N
T
E
M
P
L
A
M
P
O
N
V
O
L
.
+
V
O
L
.
-
A
U
T
O
K
E
Y
S
T
O
N
E
O
N
/
S
T
A
N
D
B
Y
INP
UT
M
E
N
U
A
U
T
O
S
E
T
F
A
N
T
E
M
P
L
A
M
P
O
N
V
O
L
.
+
V
O
L
.
-
AUTO
K
E
Y
S
T
O
N
E
I
N
P
U
T
V
O
L
.
+
P
L
A
Y
S
T
O
P
P
J
M
O
D
E
L
A
S
E
R
V
O
L
.
-
M
E
N
U
/
E
N
T
E
R
R
-
C
L
I
C
K
I
N
P
U
T
V
O
L
.
+
P
L
A
Y
S
T
O
P
P
J
M
O
D
E
L
A
S
E
R
V
O
L
.
-
M
E
N
U
/
E
N
T
E
R
R
-
C
L
I
C
K
I
N
P
U
T
V
O
L
.
+
P
L
A
Y
S
T
O
P
P
J
M
O
D
E
L
A
S
E
R
V
O
L
.
-
M
E
N
U
/
E
N
T
E
R
R
-
C
L
I
C
K
Approx. 5m
Approx. 15 degree
Approx. 5m
Approx. 15 degree
Approx. 5m
Approx. 15 degree
Models without document
camera
Models equipped with document
camera
CAUTION
Do not carry the projector by having the terminal cover parts.
Doing so, the projector may fall if that cover comes off, and injury or
damage may result.