Filter
Top Products
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
35
(E) 46H84 51H84 57H84 65H84
123
456
7
89
ENT
100
0
CHRTN
FAV
FAV
+10
PIC SIZE
EXIT
STOP
POP DIRECT CH MUTE SLEEP
TV/VCR PAUSE
FFREW
SKIP
/
SEARCH
SPLIT
SWAP POP CH
LIGHT
REC
CH SCAN
FREEZE SOURCE
PLAY
TV
CBL/SAT
VCR
DVD
VOLCH
FA
VORITE
ENTER
DVDMENU
MENU
T
O
P
M
E
N
U
G
U
I
D
E
C
L
E
A
R
E
N
T
E
R
Using the POP double-window feature
The POP (picture-out-picture) feature splits the screen into a double
window that allows you to watch two programs at the same time. The
POP program can come from a TV broadcast or an external source,
such as a VCR.
To display a TV broadcast in the POP window:
1. Press SPLIT to display the POP window.
ANT 1
POP
12
MAIN
6
2. Select channels of the POP window in the following two ways:
• To change to a specific channels, press POP DIRECT CH.
While “POP” is on the screen, press the Channel Number
buttons (0-9 and 100).
• To change the next programmed channels, press POP CH
zy.
If the V-CHIP feature is active and you try to watch a TV
program that exceeds your set rating limits, the program will be
blocked (see “Using the V-CHIP menu” on page 39).
BLOCKED
POP
24
To display a picture from an external source in the POP window:
1. Connect the external source equipment (see “Connecting your
TV” on page 8).
2. Select the TV program you want to watch in the main window.
3. Press SPLIT to display the POP window.
4. Repeatedly press SOURCE to select the input source for the POP
window (VIDEO 1, VIDEO 2, VIDEO 3, ColorStream HD1,
ColorStream HD2 or HDMI). The current source will display in
purple.
5. You can play a tape as the POP picture, or select a channel for the
POP window using the VCR’s channel keys.
POP SOURCE SELECT I ON
0 : TV
1
VIDEO
V1 :
2 :
3 :
4 : Color Stream HD1
5 : Color Stream HD2
IDEO
2
VIDEO
3
6 : HDM I
0 - 6 : TO SELECT
While the above menu is on the screen, you can select the desired
signal input source by pressing the corresponding number button
(0-6).
To close the POP window:
Press SPLIT again or EXIT.
POP CH zy
SPLIT
SOURCE
Main window
(480i only)
POP window
NOTICE OF POSSIBLE ADVERSE
EFFECTS ON TV PICTURE TUBE
Avoid displaying stationary images on
your TV screen for extended periods of
time. Fixed (non-moving) images (such
as still PIP/POP windows or black/gray
bars in wide-screen picture or PIP/POP
formats) can become permanently
engrained in the picture tube. This type
of damage is NOT COVERED BY
YOUR WARRANTY because it is the
result of misuse. See item 33 on page 4.
EXIT
POP DIRECT CH
Channel
Numbers
Note:
• The SPLIT buttons on the remote control
operate the TV’s POP features.
• You cannot display the signal other than
480i format program in the Main window.
Only the audio signal is output.
• You cannot display the ANT-2 signal source
in the POP window.
• You can choose to output the sound of
either the main or POP program (see
“Selecting the Audio OUT sound” on page
56).
• You can choose to hear the speaker sound
of either the main or POP program (See
“Switching the speaker sound of main and
POP programs” on page 36).
• HDMI, 720p ColorStream, 480p
ColorStream, and 1080i ColorStream
signals will only display in the POP (right)
window. These signals will not display in the
main (left) window when the TV is in
double-window mode.
• If an HDMI or ColorStream source is being
viewed when you open the POP double-
window feature, the HDMI or ColorStream
source will default to the POP (right)
window.