A SERVICE OF

logo

Open as PDF
next previous
1030A Operating Manual
Genelec Document D1030AR001 Copyright Genelec Oy 3.2003. All data subject to change without prior notice
www.genelec.com
AMPLIFIER SECTIONCROSSOVER SECTION
SYSTEM SPECIFICATIONS
Lower cut-off frequency, -3 dB:
< 52 Hz
Upper cut-off frequency, -3 dB:
> 20 kHz
Free field frequency response of system:
55 Hz - 18 kHz (± 2.5 dB)
Maximum short term sine wave acoustic output on
axis in half space, av er aged from 100 Hz to 3 kHz:
@ 1m
> 105 dB SPL
@ 0.5m
> 111 dB SPL
Maximum long term RMS acoustic output in same
conditions with IEC weighted noise (limited by
driver unit pro tec tion cir cuit):
@ 1m
> 99 dB SPL
@ 0.5m
> 105 dB SPL
Maximum peak acoustic output per pair above
console top, @ 1 m from the engineer with music
ma te ri al:
> 115 dB
Self generated noise level in free field @ 1m
on axis:
< 10 dB (A-weighted)
Harmonic distortion at 90 dB SPL @ 1m on axis:
Freq:
60...150 Hz
< 3%
> 150 Hz
< 0.5%
Drivers:
Bass 170 mm (6 1/2") cone
Treble 19 mm (3/4") metal dome
Both drivers are magnetically shielded.
Weight:
7,6 kg (17 lb)
Dimensions:
Height
312 mm (12 1/4")
Width
200 mm ( 7 7/8")
Depth
240 mm (9 7/16")
Bass amplifier short term output power with a
4 Ohm load:
80 W
Treble amplifier short term output power with an
8 Ohm load:
50 W
Long term output power is limited by driver unit
protection circuitry.
Amplifier system distortion at
nominal out put:
THD
< 0.08%
SMPTE-IM
< 0.08%
CCIF-IM
< 0.08%
DIM 100
< 0.08%
Signal to Noise ratio, referred to full out put:
Bass
> 95 dB
Treble
> 95 dB
Mains voltage:
230, 100/200 or 115/230V
according to region
Voltage operating range:
±10%
Power consumption:
Idle
10 VA
Full output
100 VA
Input connector XLR female:
pin 1 gnd
pin 2 +
pin 3 -
Input impedance:
10 kOhm bal anced
Input level for 100 dB SPL output @ 1m:
variable from +6 to -6 dBu
Input level for maximum short term sine wave output
of 105 dB SPL @ 1m:
variable from +11 to -1 dBu
Subsonic filter below 50 Hz :
18 dB/octave
Ultrasonic filter above 25 kHz:
12 dB/octave
Crossover frequency, Bass/Treble:
3.5 kHz
Crossover acoustical slopes:
24 - 32 dB/octave
Treble tilt control operating range in 2 dB steps:
from +2 to -4 dB & MUTE
Bass roll-off control operating range in 2 dB steps:
from 0 to -8 dB @ 50 Hz
Bass tilt control operating range in 2 dB steps:
from 0 to -6 dB @ 100 Hz
& MUTE
The 'CAL' position is with all tone con trols set to 'off'
and the input sensitivity con trol to maximum (fully
clockwise).
International enquiries:
Genelec, Olvitie 5
FIN-74100, Iisalmi, Finland
Phone +358 17 83881
Fax +358 17 812 267
Email genelec@genelec.com
In the U.S. please contact:
Genelec, Inc., 7 Tech Circle
Natick, MA 01760, USA
Phone +1 508 652 0900
Fax +1 508 652 0909
Email genelec.usa@genelec.com
In China please contact:
Genelec China Representative Office
Soho New Town, 88 Jianguo Road
D-1504, Chaoyang District
Beijing 100022, China
Phone +86 10 8580 2180
Fax
+86 10 8580 2181
Figure 4. The upper curve group shows the horizontal directivity
characteristics of the 1030A in vertical configuration measured at 1 m.
The lower curve is a 1/3 octave band power response, measured in an
IEC approved reverberation chamber.
Figure 5. The curves show the effect of the bass tilt, treble tilt and
bass roll-off controls on the free field response.
AUDIO
PRECISION
1030anec
vs
14
JAN
94
12:34:40
55
60
65
70
75
80
85
90
90
95
95
100
100
LEVEL(dBr)
20
100
1k
10k
20k
FREQ(Hz)
0
15
30
45
AUDIO
PRECISION
1030anec
vs
14
JAN
94
12:09:56
50
55
60
65
70
75
80
85
90
95
100
LEVEL(dBr)
20
100
1k
10k
20k
FREQ(Hz)
TREBLETILT
BASSROLL-OFF
BASS
TILT