A SERVICE OF

logo

Open as PDF
next previous
6. NetCommand 61
Before You Begin
1. ConnectyourA/VdevicestotheTVandconnect
yourA/VreceivertotheaudiooutputsontheTV
andtheDVDplayer.Seechapter3,“TVConnec-
tions,”forsuggestions.
2. Openthe Inputs > AVRmenu.
Note: ThetermsInput 1–Input 4usedintheAVR
screenaretemporaryplaceholdernames.They
refertotheA/VreceiverinputsforwhichtheTV
canlearnIRcodes.
Setup1:AutomaticA/VReceiverSwitchingtoItsTV
Audio Input
MostdevicesaresetupliketheVCRinthisexample,in
whichanalogaudiofromthedeviceissentthroughthe
TV.
Usethissetupfor:
• Sourcesprovidingonlyanalogstereooutput,such
asaVCR.
• Audiofrom
ANT 1
and
ANT 2
57
"/5
"/5
BVEJPWJEFP
*ODPNJOH
$PBYJBM$BCMF
UP"/5"/5
"73FDFJWFS
%7%BVEJP
JOQVU
57BVEJPJOQVU
57BVEJP
PVU
BVEJPPVUQVUGSPN
57EJHJUBMPSBOBMPH
BOBMPHBVEJP
WJEFP
WJEFP
BOBMPHBVEJP
BOBMPHBVEJP
7$3XJUI
"OBMPH"VEJP0VUQVU
Setup1: A/V receiver audio from the TV’s digital or
analog audio output (
DIGITAL AUDIO OUT
or
AVR AUDIO
OUTPUT
)
1. UnderLearn/Name,navigatetohighlightthearea
nexttoInput 1.
Inthisexample,theIRcodefortheA/Vreceiver’s
TV Audio
inputwillbe“learned”asInput 1.
2. Press
ENTER
ontheTV’sremotecontrol.
3. WhilethetextInput1isflashing,pressandholdthe
TV INPUT
keyontheA/V receiver’sremotecontrol.
4. WhenacheckappearsnexttoInput 1,releasethe
TV INPUT
key.
• Ifthetextstopsflashingbeforethecheckmark
appears,repeatthisstep.
Setup to Control Automatic Switching of
A/V Receiver Audio Inputs
Twodifferentsetupsaredescribedhere:
Setup 1:AutomaticA/VReceiverSwitchingtoTV
AudioInput
Setup 2:AutomaticA/VReceiverSwitchingfora
devicesendingaudiodirectlytotheA/Vreceiver
• AudioAvailablefromTVonly:UseSetup1.
Audiofrom
ANT 1
and
ANT 2
mustbesenttothe
A/VreceiverfromtheTV’sDIGITAL AUDIO OUTor
analog
AVR AUDIO OUTPUT
.
UseSetup1tomaketheA/Vreceiverswitchto
itsdesignatedTVaudioinputwhenviewingthese
sources.
• HDMIDigitalStereoAudio:UseSetup1
DigitalstereoaudiofromanHDMIconnection
isavailablebothindigitalformat(fromtheTV’s
DIGITAL AUDIO OUT)jackandinanalogformat
(fromtheTV’s
AVR AUDIO OUTPUT
jack).
• AnalogStereoAudio:UseSetup1.
Audiofromsourceswithonlyanalogstereooutput
(suchasaVCR)canbesenteitherdirectlytothe
A/VreceiverorthroughtotheTVandthenontothe
A/Vreceiver.
Mitsubishirecommendsyousendaudiothrough
theTVasshownintheexample.Setup1causes
theA/Vreceivertoswitchtoitsinputdesignatedfor
TVaudio.
IfyouhaveadigitalA/Vreceiver,theTVmakesthe
audioavailablebyconvertinganalogaudiotoa
digitaloutput.
• DigitalSurroundSound:UseSetup2.
Adevicecansenddigitalsurroundsoundsuchas
DolbyDigitalorDTSdirectlytotheA/Vreceiver,
bypassingtheTVentirely.Thedevicemightbe
aDVDplayer,cablebox,orsatellitereceiver,and
Setting Up NetCommand Control of
an A/V Receiver, continued
IMPORTANT
To hear audio sent from the TV to the A/V
receiver, you must have:
•
physically connected the TV to the A/V
receiver
•
selected the A/V receiver as the audio
source. Press AUDIO, then
to show the
Speakers option,
then
to select the A/V
Receiver.
• “
learned” the IR codes for the A/V receiver
inputs
• chosenthecorrectinputinthe
NetCommand A/V Receiver Learn screen
couldhaveHDMIoutput.ADVDplayerisusedin
thisexample.
Yoursetupmayincludeadditionaldeviceswith
digitalsurroundsoundconnecteddirectlytothe
A/Vreceiver.ThesedevicesmightbeaDVDplayer
plusacableboxorsatellitereceiver.