Bryston BR2 Universal Remote User Manual


  Open as PDF
of 4
 
PROGRAMMING THE BCD-1 via the BR2 REMOTE CONTROL:
Press the CODE button on the remote control until the red LED lights and then enter the 3 digt code as listed below. The LED
will flash to confirm transmission and then extinguish.
242: To enable toggling the display ON or OFF. After entering code 242 the zero button can be used to toggle the
displayonoroff.Reversethisproceduretodeactivatethisdisplayon/offfunction
Enable or disable the External (remote) Trigger:
1st) PlacetheBCD-1instandbymodebypressingthePOWERbuttononeithertheBCD-1itselforontheremote
controluntiltheredstandbyLEDonthefrontpaneloftheBCD-1(immediatelyabovethefrontpanelPOWER
button) lights.
2nd) PresstheCODEbuttonmomentarilyuntiltheredLEDiscontinuouslylit.
3rd) Enterthecode241.EverytimethecodeissuccessfullyenteredthestateoftheExternalTriggerwilltoggle
betweenenabledanddisabledandthestatusoftheExternalTriggerwillbedisplayedonthealpha-numeric
displayfor2to3seconds.
TheExternalTriggerutilizesacontrolvoltage(3to12volts,eitherACorDC)connectedtotheTRIGGERIN
portontherearoftheBCD-1.Awire-clampconnectorthatmateswiththeTRIGGERINportisprovidedwith
everyBCD-1(Seepage2forwiringdetails).OnceenabledtheBCD-1willonlybepoweredonwhenacontrol
voltageof3-12VAC/DCat≥3mAispresent.AssoonasthecontrolvoltageiswithdrawntheBCD-1willpower
downandgointostandbymode.
For more information see the BCD-1 Owners Manual
PROGRAMMING THE BDA-1 via the BR2 REMOTE CONTROL:
Press the CODE button on the remote control until the red LED lights and then enter the 3 digt code as listed below. The LED
will flash to confirm transmission and then extinguish.
021: source OPTO-1 026: sourceSPDIF-4 250: Output level 0dB
022: source OPTO-2 027: sourceAES/EBU 251: Output level -1dB
023: sourceSPDIF-1 028: sourceUSB 252: Output level -2dB
024: sourceSPDIF-2 029: PowerON/OFF 253: Output level -3dB
025: sourceSPDIF-3 030: UpsamplingON/OFF
Codes 021 thourgh 030 mimic the actions of the corresponding dedicated buttons on the BR2. These codes can also be
senttotheBDA-1viatheRS232controlporttofacilitatetheuseofsystemcontrollerssuchasthoseprovidedbyAVX,
Crestron, etc.
For more information see the BDA-1 Owners Manual
IMPORTANT SAFETY INSTRUCTIONS:
The lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of un-insulated “dangerous voltage “
within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not use or store near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
8. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
DO NOT EXPOSE THIS EQUIPMENT TO DRIPPING OR SPLASHING AND ENSURE THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, ARE PLACED
ON THE EQUIPMENT.
 previous