Filter
Top Products
AUDIO Setup Codes
Compact Disc
ADC 318
Akai 249 261
Aiwa 176
Carver 176
Crown 154
Denon 273
Fisher 230 274
Goldstar (LG) 308
Harman Kardon 315
JVC 297
Kenwood 131 176 274 289 299
Krol 176
LG (Goldstar) 308
Magnavox (Philips) 037 084 119 296
Mission 176
Mitsubishi 245 249
NAD 182 231 290
Nakamichi 264 319
NEC 235
NSM 176
Onkyo 300
Panasonic 184 266
Philips (Magnavox) 037 084 119 296
Pioneer 116 127
Quasar 184
Radio Shack 186 190 266 279 289
RCA 295
Sanyo 230 309
SAE 176
Scott 186
Sharp 288 289
Sony 067 292 293
Soundesign 148 242 311 320
STS 318
Sylvania 084
Teac 186
Technics 184 208 317
Toshiba 290
Yamaha 280
Receiver / Amplifier
Adcom 325
Aiwa 301
Akai 142
Bose 302
Carver 155 180
Denon 262 307
Everquest 136
Fisher 063 180
Fosgate Audionics 305
Goldstar (LG) 036
Harman Kardon 130 257 305 306
Hitachi 240
Jensen 140
JVC 114 241
Kenwood 063 277
LG (Goldstar) 036
Luxman 281
Magnavox 080
Marantz 282 283 284 285
NAD 286
Onkyo 126 171 304
Optimus 142 229 321
Panasonic 032 074
Parasound 323
Philips (Magnavox) 080
Pioneer 123 137 251 298
Quasar 032
Radio Shack 229 267
Realistic 226 268
Rotel 310
Sansui 283
Sanyo 195
Scott 272
Sharp 294
Sherwood 229 267
Sony 041 057 232 287
Soundesign 083 088 239 265
SSI 313
Taekwang 142
Teac 314 316
Technics 032
Wards 063
Victor 114 241
Yamaha 145 254 303
Zenith 036 083 088 239 265
7. Code Number Read-Back
To identify the 3-digit setup codes stored under the
Point and Press
®
programming method, follow these
steps:
To identify the TV setup code…
1. Press [TV], then [SELECT] together
until the [TV]
button illuminates.
2. Press [INFO]. The [TV] button will “blink back” the
code numbers, with a 1-second interval between
each digit of the code.
Example: For code “035”, the remote will blink
10 times, then 3 times, then 5 times.
To identify the 3-digit VIDEO code, press [VIDEO],
then [SELECT] in step 1, then press [INFO].
To identify the 3-digit AUDIO code, press [AUDIO],
then [SELECT] in step 1, then press [INFO].
8. [ALL] Button
Once you have programmed each of your devices,
press [ALL] to turn all of them on / off with a single
button press. You can also program the [ALL] button
to tune your TV to its correct output channel.
Programming the [ALL] Button
If you would like the [ALL] button to also tune your TV
to its correct output channel (typically 3) follow these
steps:
1. Press [MODE], then [CBL] to select the remote’s
cable mode.
2. Press [SETTINGS], then [ALL] together until the
[TV] button illuminates.
3. Press [0], then [3] X,Y.
4. Press [CH S] to store the TV channel. The [TV]
button will blink 3-times and go out.
X Your TV output channel may also be 2 or 4. If you
are not sure, contact your cable operator.
Y Depending on your TV brand, the channel may
have to be entered as “3”, “03” or “003”.
Using the [ALL] Button
When pressing the [ALL] button, be sure to keep the
remote control aimed at your electronic devices until
your electronic devices turn on or / off.
Resetting the [ALL] Button