Filter
Top Products
46 47
The others
Before doubting about troubles (VCR)
¥ Recording a TV program is impossible.
¥ Once pressing [REC], a videotape is
ejected automatically.
¥ Timer recording of Cable TV does not
work.
¥ In spite of pressing [CHANNEL], a
channel can not be set.
¥ While duplicating, screen is not clean
and distorted.
¥ remote control does not work.
¥ Buttons on remote control do not
work.
¥ VISS index search does not work.
¥ Cable broadcasting can not be
selected.
Checks
Symptom
➤ Please check whether a channel is fixed on video. If not, you have to
turn it into ÒTVÓ by pressing [OUTPUT] button.
➤ Please check whether the timer recording info is right.
➤ Are RF cables inputted antenna connection terminal correctly?
➤ Does a CH number selected in display section appear?
➤ Please check a tab on a tape whether it is broken or not. (If it was
broken, please scotch-tape it)
➤ Check whether the screen is displayed in VCR Only Channel. Press
[OUTPUT] button in this remote controller to adjust in "General
Broadcast" condition.
➤ Is the rounded line (RF cable) connected in "ANT.IN" terminal?
➤ Please check whether the clock is right.
➤ Does the display on your video show Ò
Ó
(Ready to timer recording)?
Please make it out.
➤ Please check whether the timer recording info is right.
➤ Please check a tab on a tape whether it is broke or not. (If it was
broken, please scotch-tape it)
➤ Was a cable data output code connected correctly?
➤ Were a converter manufacturer setup and output channel right?
➤ Did you enter a password? (Please cancel it.)
➤ Did you turn off your player? (Please turn it on.)
➤ You may not memorize channels.
➤ Please check your channel setting or press a number button.
➤ Some tapes or discs distributed in the market for lending is set to
prevent copy in manufacturing. These tapes cannot be duplicated in
a good condition.
➤ Battery may be weak or exhausted.
➤ A receiver of remote control may be different with a sender.
➤ In case a videotape is positioned in the beginning, ÒVISS REWÓ and
ÒREWÓ do not work.
➤ In case a videotape is positioned in the end, ÒFFÓ, ÒVISS FFÓ, ÒPLAYÓ
and ÒRECÓ do not work.
➤ Please check whether another button is pressed.
➤ Are you playing a tape that is not recorded in this recorder? (Try to
record it with the recorder.)
➤ You may start recording it in ÒREC-PAUSEÓ. Please start recording it
from stop condition.
➤ Please select ÒCABLEÓ not ÒNETWORKÓ from the ÒCHANNEL SETTINGÓ.
Before doubting about troubles (VCR)
¥ ÒPower OnÓ does not work.
¥ It does not work even in ÒPower OnÓ.
¥ A videotape is not inputted in.
¥ On inputting a videotape, the tape is
re-ejected.
¥ A videotape is not ejected.
¥ A channel on video and a play screen
does not appear.
¥ Noise (screen noise) appears on
screen.
¥ Noise appears on screen after
recording.
¥ While in playing, noise appears.
¥ Sound and screen are irregular.
¥ Sound comes out but screen does not
appear.
¥ Screen is irregular and stripes appears.
¥ "Screen Error" message is displayed in
a screen.
¥ While recording and playing, the top
of screen extremely waves.
¥ A screen is not clear.
¥ A screen at pause is trembling or slow
screen is not clear.
Checks
Symptom
➤ Please check whether a power plug is inserted in an electric outlet.
➤ Please check whether a videotape is inserted in.
➤ Try to insert a plug again.
➤ Please check whether a power plug is inserted in an electric outlet.
➤ Please check whether a videotape is in.
➤ Please check whether a videotape is inserted in a right direction (a
side of transparent window should be on the upside)
➤ Have you inputted a videotape again just after the tape was ejected?
Please try it again after fully ejecting it.
➤ When a videotape forces to be ejected, the tape may not be inputted.
In the case, please pull out an outlet, and then push the tape
smoothly.
➤ ThatÕs why a safe mode to protect a videotape is operated
automatically. Please pull out the tape and input it again.
➤ In case the product is used for a long time, a videotape may not be ejected
for a film inside may be stretched. In the case, please pull out a power plug
for about 10mins and then press [EJECT] button.
➤ Please check your antennaÕs connection.
➤ TV channel should be fixed on video channel (3 or 4).
➤ Please check your antennaÕs signal whether it may be weak. In case of
its weakness, please use a frequency amplifier connected with the
device.
➤ Press [TV/VCR] and then let ÒVCRÓ is displayed on the display panel.
➤ While in no use of VCR, was it turned on?
➤ While in recording a program, do you watch another channel?
➤ Select TV by pressing [TV/VCR] button on remote control.
➤ While in playing a videotape, there may happen some noise or blot in
the part of the beginning of a videotape or resuming ÒPAUSEÓ, which
are not breakdown.
➤ Please press [TRACKING] for better screen. Videotape may be poor.
Try to change it to another one.
➤ Please use a head-cleaner to clean VCR heads. VCR heads may be
contaminated.
➤ Since VCR Play signals are not stable like a TV signals, screen may be
unstable or curved while in playing. To fix the problem, please
horizontal adjustment.
➤ In case videotape is the one recorded by other products or old one,
stripe may appear on the screen.
➤ Try to adjust the screen by [TRACKING+/Ð] button.
➤ Try to use a head-cleaner.
➤ Try to use a head-cleaner.
➤ Try to adjust the screen by [TRACKING+/Ð] button.