Filter
Top Products
52
Before suspecting a fault (VCR)
• “Power On” does not work.
• It does not work even in “Power On”.
• A videotape is not inputted in.
• On inputting a videotape, the tape is
re-ejected.
• A videotape is not ejected.
• A channel on video and a play screen
does not appear.
• Noise (screen noise) appears on
screen.
• Noise appears on screen after
recording.
• During playback, noise appears.
• Sound and picture are poor.
• Sound comes out but picture does not
appear.
• Picture is irregular and stripes appears.
• "Picture Error" message is displayed
on the screen.
• While recording and playing, the top
of screen waves.
• The picture is not clear.
• A picture at pause is trembling or
slow screen is not clear.
Checks
Symptom
➤ Please check whether the power plug is inserted in an electric outlet.
➤ Please check whether a videotape is inserted in.
➤ Try to insert the plug again.
➤ Please check whether a power plug is inserted in an electric outlet.
➤ Please check whether a videotape is in.
➤ Please check whether a videotape is inserted in a right direction (
If
the machine won’t allow you to insert a tape,
the side of transparent
window should be on the upside)
➤ Have you inputted a videotape again just after the tape was ejected?
Please try it again after fully ejecting it.
➤
It may not be in squarely. For correct operation you must insert the tape smoothly.
➤ That’s why a safe mode to protect a videotape is operated
automatically. Please pull out the tape and input it again.
➤
In case the product is not used for a long time, a videotape may not be
ejected because the film inside may be stretched. In this case, please pull
out a power plug for about 10mins and then press the “EJECT” button.
➤ Please check your antenna’s connection.
➤ TV channel should be stored on video channel.
➤
Please check your antenna’s signal whether it may be weak. If it is weak,
please use an (RF) radio frequency amplifier connected with the device.
➤
Press “TV/VCR” and then ensure “VCR” is displayed on the display panel.
➤ Check if VCR, was it turned on?
➤ While in recording a program, do you watch another channel?
➤ Select TV by pressing [TV/VCR] button on remote control.
➤ While in playing a videotape, there may be some noise or blot in the
part of the beginning of a videotape or resuming “PAUSE”. This is
not a fault.
➤ Please press “TRACKING” for better screen. Videotape may be
poor. Try to change it to another one.
➤ Please use a head-cleaner to clean VCR heads. VCR heads may be
contaminated.
➤ Since VCR Play signals are not stable like a TV signals, screen may
be unstable or curved while playing. This normally occurs on older
TV’s which may have a specific channel for VCR playback.
➤ If videotape is the one recorded by other products or old one, stripe
may appear on the screen.
➤ Try to adjust the picture by [TRACKING+/-] button
➤ Try to use a head-cleaner.
➤ Try to use a head-cleaner.
➤ Try to adjust the screen by [TRACKING+/-] button.
53
Before suspecting a fault (VCR)
• Recording a TV program is
impossible.
• Once pressing “REC”, a videotape is
ejected automatically.
• Timer recording of Cable TV does
not work.
• In spite of pressing “CHANNEL”, a
channel can not be set.
• While duplicating, screen is not
clean and distorted.
• remote control does not work.
• Buttons on remote control do not
work.
• VISS index search does not work.
• Cable broadcasting can not be
selected.
Checks
Symptom
➤ For recording, you should use a videotape with a tab.
➤ Please check whether a channel is fixed on video. If not, you have to
turn it into “TV” by pressing “INPUT” button.
➤ Please check whether the timer recording info is right.
➤ Are RF cables in the antenna connection terminal correctly?
➤ Does a CH number selected in display section appear?
➤ Please check a tab on a tape whether it is broken or not. (If it was
broken, please replace with some adhesive tape)
➤ Please check whether the clock is right.
➤ Does the display on your video show “
”
(Ready for timer
recording)?
➤ Please check whether the timer recording info is right.
➤ Please check a tab on a tape whether it is broke or not. (If it is broken,
please replace with some adhesive tape)
➤ Was the cable data output code connected correctly?
➤ Was the cable box setup and output channel right?
➤ Did you enter a password? (Please cancel it.)
➤ Did you turn off your player? (Please turn it on.)
➤ You may not have memorized your channels.
➤ Please check your channel setting or press a number button.
➤ Some tapes or discs distributed in the market for lending is set to
prevent copy in manufacturing. These tapes cannot be duplicated in
a good condition.
➤ Battery may be weak or exhausted.
➤ Are you using the correct remote.
➤ In case a videotape is positioned at the beginning, “VISS REW” and
“REW” do not work.
➤ In case a videotape is positioned at the end, “FF”, “VISS FF”, “PLAY”
and “REC” do not work.
➤ Please check whether another button is pressed.
➤ Are you playing a tape that is not recorded in this recorder? (Try and
record it with the recorder.)
➤ You may start recording it in “REC-PAUSE”. Please start recording it
from stop condition.
➤ Please select “CABLE” not “NETWORK” from the “CHANNEL
SETTING”.
The others