Dynex DX-32L150A11 Flat Panel Television User Manual


 
Understanding the basics
13
DX-32L/37L/40L/46L
Notes:
During auto scan, digital programs will be scanned first, then analog
programs. When all available digital programs have been searched,
the screen will ask you to “Press MENU or EXIT if you don’t need
analog channel scan.” At this point you can press EXIT to exit the
analog channel scan, or just ignore it and the TV will go on scanning.
Channel scan can take up to 30+ minutes.
•You can press EXIT at any time to stop the auto scan, but you will
need to run the auto scan again to create a channel list.
12 Select the corresponding video input source through the INPUT
SOURCE menu.
Understanding the basics
Turning your TV on or off
To turn your TV on or off (standby mode):
1 Plug the power cord into an AC power outlet.
2 Press (power). Your TV turns on.
3 Press again to turn off your TV. When you turn off your TV, it
goes into standby mode.
Warning: When your TV is in standby mode, it is still receiving power. To
completely disconnect power, unplug the power cord.
Note: If your TV does not receive an input signal for several minutes, it
automatically goes into standby mode.
Selecting the video input source
To select the video input source:
1 Turn on your TV, then press the INPUT key on the remote, or the
INPUT button on the TV. The INPUT SOURCE menu opens.
2 Press or to highlight the video source, then press ENTER.
You can also select the input source using the following remote
control buttons:
COMP—Press repeatedly to cycle between Component
inputs.
HDMI–Press repeatedly to cycle between HDMI inputs.
VIDEO—Press repeatedly to cycle between AV and S-Video
inputs.
TV—Press to switch to TV mode.
VGA—Press to view a computer connected to your TV.
Selecting a channel
To select a channel:
Press CH / CH to go to the next or previous channel.
Press the number buttons to enter the channel number you
want, then wait for the channel to change, or press ENTER to
change the channel immediately.
To select a digital channel, press the number buttons to
select the main digital channel, then press the dot (.) button,
then the number buttons again to select the sub-channel.
Wait for the channel to change or press ENTER to change the
channel.
Note: Button presses must be within three seconds of each other.
Press RECALL to go to the last channel viewed.
Press CH-LIST to display a list of memorized channels, press or
to select the channel you want from the list, then press ENTER
to go to that channel.
Press FAVORITE to display a list of your saved favorite channels,
press or to select the channel you want from the list, then
press ENTER to go to that channel.
Note: If the list has more than one page, press or to scroll through
the pages.
Adjusting the volume
To adjust the volume:
Press VOL+ or VOL– to increase or decrease the volume.
Press MUTE to temporarily turn off all sound. Press MUTE again
to restore the sound.
Displaying program information
To display program information:
Press INFO to show an information banner. The information
banner shows current program information such as channel
number, video input source, and resolution.
Digital signal information—Displays channel number,
station name, channel label (if preset), broadcast program
name, TV rating, signal type, audio information, resolution,
CC mode, current time, and current program start and end
times when watching a digital channel.
Analog signal information—Displays channel number,
channel label (if preset), signal type, audio information, and
resolution when watching an analog channel.
Press GUIDE to show the digital program guide, which may show
a list of available programs, program times, and program
summaries, depending on the information provided by the
broadcaster.
On-screen menu overview
Picture menu
Picture
Select
Move
MENU
Exit
Picture Mode
Contrast
Brightness
Color
Tint
Advanced Video
Audio Setup Channel
Custom
70
40
60
0
Sharpness
50
Backlight
30
DX-32L-37L-46L150A11_10-0012.book Page 13 Thursday, January 14, 2010 8:30 AM