Filter
Top Products
[TV RATING SET UP]
4) Press [CH K / L] to select a rating.
5-1) * Rating with no sub categories
Press
[VOL K] at either rating to set to [BLOCK] or [VIEW].
5-2) * Rating with sub categories
Press
[VOL K] twice. Press [CH K / L] to select a rating.
Press [VOL K] to set to [BLOCK] or [VIEW].
GENERAL SPECIFICATIONS
Television system: NTSC-M
TV Standard
Closed Caption
System: §15.119/FCC
Channel coverage
VHF: 2 ~ 13
UHF: 14 ~ 69
CATV: 2 ~ 13, A ~ W,
W+1 ~ W+84,
A-5 ~ A-1, 5A
Tuning System: 181 channel
frequency synthesized
tuning system
Channel access: Direct access keyboard,
programmable
scan and up/down
Terminals
Antenna input: VHF/UHF/CATV
75 ohm unbalanced
(F-type)
S-Video input: Mini DIN 4-pin jack
Video input: RCA connector x 1
Audio input: RCA connector x 4
(2 (L/R) x Front / 2 (L/R) x Rear)
Headphone: 1/8" stereo (3.5mm)
Stereo Sound System
2 speakers
ELECTRICAL SPECIFICATIONS
Sound output: 1W, 8 ohm x2
OTHER SPECIFICATIONS
Remote control: Digital encoded
infrared light system
Operating
temperature: 5°C to 40°C
(41°F~104°F)
Power requirements: AC120V, 60Hz
Power consumption
(Maximum): 74W
Picture tube: 20"
Dimensions: H : 17-1/8" (435mm)
W: 19-15/16" (506mm)
D: 17-15/16" (455mm)
Weight: 44.1 lbs. (20kg)
•Designs and specifications are subject to
change without notice and without our
legal obligation.
•If there is a discrepancy between languages,
the default language will be English.
SPECIFICATIONS
OPTIONAL SETTINGS (Continued)
MAINTENANCE
TROUBLESHOOTING GUIDE
Sometimes a performance problem can be easily solved by checking seemingly apparent but often over-
looked possibilities. Before arranging for service, check these items. It could save your time and money.
QUICK SERVICE CHECK LIST
PROBLEM
POSSIBLE REMEDY
Try a new channel, if OK, then possible station trouble.
Is TV plugged in? Power at outlet?
Is TV’s power on?
Is antenna or cable connected to terminal on the back of the set?
If outside antenna is being used, check for broken wire or loose connection.
Check for local interference.
Turn off the TV and then turn it on after about a minute.
Adjust COLOR control.
Adjust CONTRAST & BRIGHT control.
Check batteries in remote control.
Move the TV away from the nearby appliances which generate a magnetic field.
Turn off using [POWER], then turn it on again 30 minutes later or so.
Check if there is an obstacle between the sensor and the remote control.
Test the signal output.* If OK, then possible remote sensor trouble.
Remote control doesn’t work
Bars on screen
Picture distorted
Picture rolls vertically
No color
Poor reception on some channels
Weak picture
Lines or streaks in picture
Ghosts in picture
Picture blurred
Sound OK, picture poor
Picture OK, sound poor
No Picture or sound
Different color marks on screen
*Tune an AM radio to a band with no broadcasting. Press a button on the remote control toward the radio. Sound will be fluttering
when you press any key and the radio receives the signal. This means the remote control unit is working.
Closed Caption Problem Possible Remedy
Misspelled captions are shown.
Text is not shown in its entirety
or there is a delay of what is being said.
Captions are scrambled with white boxes
on the TV screen.
No captions are displayed in a program
which must contain closed caption.
No captions are displayed when playing a
prerecorded videotape with closed caption.
The TV screen shows a black box.
Spelling errors may pass through uncorrected by the closed caption-
ing production company in a live broadcast.
Captions that are delayed a few seconds behind the actual dialogue
are common for live broadcasts. Most captioning production compa-
nies can display a dialogue to a maximum of 220 words per minute.
If a dialogue exceeds that rate, selective editing is used to insure that
the captions remain up-to-date with the current TV screen dialogue.
Interference caused by building, power lines, thunderstorms, etc.
may cause scrambled or incomplete captions to appear.
Broadcasters may use a time compression process to the actual pro-
gram so that additional advertising time can be given. In this case,
captions will be lost since the decoder cannot read the compressed
information.
The videotape may be either an illegal copy or the tape duplicating
company may accidentally have left out the captioning signals dur-
ing the copying process.
You are in TEXT mode. Select CAPTION [C1], [C2] or [OFF].
CABINET CLEANING
●
Wipe the front panel and other exterior sur-
faces of the TV with a soft cloth immersed
in lukewarm water and wrung dry.
●
Never use a solvent or alcohol. Do not spray
insecticide liquid near the TV. Such chemi-
cals may cause damage and discoloration to
the exposed surfaces.
PICTURE TUBE CLEANING
Wipe the picture tube of the TV with a soft
cloth. Before cleaning the picture tube, discon-
nect the power cord.
SUPPLIED ACCESSORIES
●
Owner’s Manual
(1EMN21393)
●
Remote control unit
(NE116UE)
●
Batteries
(“AA” x 2)
V-CHIP SET UP
[CHANGING THE ACCESS CODE]
4) Press the Number buttons to enter your old access code.
5) Press [MENU] to exit the menu.
NEW CODE
COMFIRM CODE
[[[[
_ _ _ _
TV-Y
[VIEW]
TV-Y7 (
)
[VIEW]
TV-G
[VIEW]
TV-PG
( )
[VIEW]
TV-14
( )
[VIEW]
TV-MA (
)
[VIEW]
<Selection> <Rating Category Explanations>
• TV-Y : Appropriate for all children
• TV-Y7 : Appropriate for children seven and older
• TV-G : General Audience
• TV-PG : Parental Guidance suggested
• TV-14 : Unsuitable for children under 14
• TV-MA : Mature audience only
TV-Y
[VIEW]
TV-Y7 (
)
[VIEW]
TV-G
[VIEW]
TV-PG
( )
[VIEW]
TV-14
( )
[VIEW]
TV-MA (
)
[VIEW]
Sub categories
This enables parents to prevent their children from watching inappropriate material on TV.
● The limitation is not available for news, sports programs, unedited movies on premium cable
channels and Emergency Broadcast System signals.
● When you try to access to a program which is blocked, “PROTECTED PROGRAM by ...”
message appears on the TV screen.
● Programming may be rated by the Motion Picture Association of America (MPAA) or accord-
ing to the Television Parental Guidelines. In order to block any inappropriate programming, set
your limits in both MPAA RATING and TV RATING.
1) Press
[MENU]. Press [CH K / L] to select “V-CHIP SET UP”, then press [VOL K].
2) Enter 4-digit access code with the Number buttons. If you have
not set up your personal access code, enter 0000 (default access
code).
3) Press
[CH K / L] to select “TV RATING”, “MPAA RATING” or
“CHANGE CODE”, then press
[VOL K].
<Selection> <Rating Category Explanations>
• TV-Y7
FV : Fantasy Violence
• TV-PG / TV-14 / TV-MA :
D : Suggestive Dialog
(TV-PG, TV-14 only)
L: Coarse Language
S : Sexual Situation
V: Violence
G [VIEW]
PG
[VIEW]
PG-13
[VIEW]
R
[VIEW]
NC-17
[VIEW]
X
[VIEW]
[MPAA RATING SET UP]
4) Press [CH K / L] to select a rating.
5) Press
[VOL K] repeatedly to set to [BLOCK] or [VIEW].
TV RATING
MPAA RATING
CHANGE CODE
G [VIEW]
PG
[VIEW]
PG-13
[VIEW]
R
[BLOCK]
NC-17
[BLOCK]
X
[BLOCK]
<Selection> <Rating Category Explanations>
• G : General Audience
• PG : Parental Guidance suggested
• PG-13 : Unsuitable for children under 13
• R : Restricted; under 17 requires accompanying parent
or adult guardian
• NC-17 : No one under 17 admitted
• X : Mature audience only
ACCESS CODE
_ _ _ _
TV-Y
[VIEW]
TV-Y7 (
)
[VIEW]
TV-G
[BLOCK]
TV-PG
(DLSV)
[BLOCK]
TV-14
(DLSV)
[BLOCK]
TV-MA (DLSV)
[BLOCK]
TV-PG
[BLOCK]
D
[VIEW]
L
[BLOCK]
S
[BLOCK]
V
[BLOCK]
6) Press [MENU] to exit the menu.
6) Press
[MENU] to exit the menu.
Notes (for TV RATING and MPAA RATING):
●
You cannot access the setup menu when the “PROTECTED PROGRAM by ...” message
appears. Move to an unblocked channel before you press [MENU].
●
When you select a rating and set it to [BLOCK], the higher ratings will be blocked automati-
cally. The lower ratings will be available for viewing.
●
When you set the lowest rating to [VIEW], all other ratings will automatically be available for
viewing.
Notes:
●
Make sure you enter exactly the same new code in the “CONFIRM
CODE” space as one in the “NEW CODE” space. If they are differrent,
the “NEW CODE” space is cleared for redoing.
●
Your personal access code will be erased and will return to the default
(0000) when a power failure occurs or when you turn off the power using
a wall switch. If you have forgotten the code, unplug the power cord for
10 seconds to restore the access code to 0000.
A
B
C
A
B
C