Extron electronic WMK 100 TV Mount User Manual


  Open as PDF
of 4
 
PRELIMINARY
3
3. Run cables
Run signal cables from the proposed PoleVault input wall plates,
control device location, and the speakers to the WMK 100 location.
Cables can be routed behind the walls, or through a surface raceway
(e.g., Wiremold 700 or 2400 series) directly to the WMK 100.
3A. If running cable behind the walls:
i. Run all the cables from the various locations to the WMK and
through the access hole.
3B. If using a surface raceway:
i. Attach the WMK cover to the base plate, then identify and
mark the most suitable raceway entrance to the WMK 100.
ii. Run the raceway from the signal source, speaker, and display
locations to the marked raceway entrance at the WMK.
iii Remove the WMK cover, and remove the desired knockout.
iv. Attach the raceway to the wall and run cables from the sources
and outputs through the raceway to the WMK.
4. Cable the switcher
a. Connect the cables from the PoleVault transmitters, control device
(MediaLink
®
Controller), speakers, and optional accessories (VoiceLift, Page Sensor Kit) to the rear ports of the
switcher (see below). Refer to the PVS 305SA Setup Guide for additional details.
N
If using a device other than a PVS 305SA (e.g., PVS 204SA Plus), refer to that device's user manual for details.
b. Run VGA and composite video cables from the switcher to the output display device through the wall or
where fitted, the raceway.
c. Connect the power supply to the switcher and plug it in to the electrical outlet.
N
If the electrical outlet is outside the WMK, pass the IEC power cable out through one of the raceway knockouts.
Raceway Option
2400
700
Signal Cable Access
Cutout Option
Figure 6 — Cabling run options
LR
LR
LR
AUX AUDIO
INPUT 5
LINE OUT
VOICELIFT
RECEIVER
PAGING
SENSOR
DO NOT
GROUND
OR SHORT
SPEAKER
OUTPUTS
1B RGB
1A RGB
2B RGB
2A RGB
3B RGB
/VIDEO
4B RGB
/VIDEO
3A RGB 4A RGB
I
N
P
U
T
S
RS-232 MLC/IR
2/4/8
Ohms
CLASS 2 WIRING
AMPLIFIED AUDIO OUT
VOL/MUTE
Tx RxIR 12V
10V 50mA
POWER
US
LISTED
17TT
AUDIO/VIDEO
APPA RATUS
®
RGB
VIDEO
OUTPUTS
CONTROL
N15779
12V
5A MAX
2A RGB
1A RGB
1B RGB
2B RGB
4A RGB
3A RGB
3B RGB
3 VIDEO
4B RGB
4 VIDEO
RGB signal input
(2 CAT 5 cables, A and B
with RJ-45 connectors)
RGB output
to display
RGB #1A
External
Power Supply
(12 VDC, 5 A max.)
d
Composite
video output
to display
Composite video input
(CAT 5 cable with
RJ-45 connector)
b
g
f
a
RS-232 Control
B
A
+12 VDC
Ground ( )
Tr ansmit (Tx)
Receive (Rx)
Ground ( )
Power
Connector
RCA
Connector
Aux Audio
Input 5
e
i
c
j
k
Line out output
(audio)
Red Positive (+)
Black Negative (-)
Wire Color
PVS Terminal
(left and right)
h
VGA
Connector
RGB #1B
VIDEO #3
CONFIG
DISPLAY
VOLUME
MLC 104 IP PLUS
ON
VCR
DVD
PC
OFF
1
2
3
4
PVT RGB D Plus
PVT CV D
COMPUTER IN
AUDIO
IN OUT
MONITOR OUT
IR OUT
S G
AUDIO IN
L
R
VIDEO IN
IR OUT
S G
Paging
Sensor
VoiceLift
Receiver
Audio output
to speakers
MLC Wire Colors PVS Switcher
A (Rx) White A (Tx)
B (Tx) Violet B (Rx)
Ground Drain Wire D (Ground)
Ground Black D (Ground)
12V In Red E +12 V
Cabling the switcher
 previous