Filter
Top Products
8 EN
To Skip a Preset Channel
The channels you can no longer receive or seldom watch can
be set to be skipped when you access channels by pressing
CHANNEL (K/L).
• Use the remote control for this procedure.
1) Press
MENU.
2) Press
PLAY/K or STOP/L to select “INITIAL”, then press
F.FW D/B.
3) Press
PLAY/K or STOP/L to select “CH TUNING”, then
press
F.FWD/B.
4) Press
PLAY/K or STOP/L to select “MANUAL”, then
press
F.FWD/B.
5) Press
PLAY/K or STOP/L to select “POSITION”, then
press
F.FWD/B.
6) Press
the
number buttons, PLAY/K, or STOP/L to select
relevant position number, then press
F.FWD/B.
7) Press
PLAY/K or STOP/L to select “SKIP”, then press
F.FW D/B to select [ON].
•To memorize the channel again, press
F.FWD/B. “ON”
will change to “OFF”.
Note for 31B-254 and 31B-454 only
•The VCR refers to the PDC channel which was
memorized into position 01 when you set the Auto
Clock.
The position 01 must therefore be set “SKIP” to [OFF].
8) Press
MENU to exit.
Note: To confirm that a channel has been deleted, press
CHANNEL (K/L).
Channel Reprogramming
You can replace two channels.
• Use the remote control for this procedure.
1) Press
MENU.
2) Press
PLAY/K or STOP/L to select “INITIAL”, then press
F.FWD/B.
3) Press
PLAY/K or STOP/L to select “CH TUNING”, then
press
F.FW D/B.
4) Press
PLAY/K or STOP/L repeatedly to select “MOVE”,
then press
F.FWD/B.
5) Press
PLAY/K or STOP/L repeatedly to select the position
number you want to change the channel, then press
F.FWD/B.
•You cannot select a position number where “- - -”
appears next to the number. This is because SKIP is set
to [ON] for this position number.
•When a weak signal is received in Channel
Reprogramming mode, you can change the background
to solid blue by pressing
TAPE COUNTER RESET.
If you press the button again, the background will return
to the static screen.
6) Press
PLAY/K or STOP/L repeatedly until the channel
move to another position number, then press
F.FWD/B.
7) Press
MENU.
INITIAL
CH TUNING
CLOCK
RF OUT
MANUAL
POSITION
CHANNEL
DECODER
SKIP
P08
008
[OFF]
[ON]
CH TUNING
AUTO
MANUAL
MOVE
MENU
TIMER
SET UP
INITIAL
INITIAL
CH TUNING
CLOCK
RF OUT
CH TUNING
AUTO
MANUAL
MOVE
MOVE
P01:
P02:
P03:
P04:
P05:
01
02
03
04
05
P06:
P07:
P08:
P09:
P10:
06
07
08
09
10
Position
Number
Channel
Number
MOVE
P01:
P02:
P03:
P04:
P05:
01
02
10
04
05
P06:
P07:
P08:
P09:
P10:
06
07
08
09
03
[ ]
MENU
TIMER
SET UP
INITIAL
MOVE
P01:
P02:
P03:
P04:
P05:
01
02
10
04
05
P06:
P07:
P08:
P09:
P10:
06
07
08
09
03
HM210BD(EN).fm Page 8 Thursday, March 2, 2006 6:07 PM