Grizzly G0706 DVR User Manual


 
BdYZa<%,%+B[\#h^cXZ&&$%.
"'("
Surface Planing
I]ZejgedhZd[hjg[VXZeaVc^c\dci]Z_d^ciZg^hid
bV`ZdcZ[VXZd[i]Zldg`e^ZXZ[aVihZZFigures
25–26#I]^h^hVcZXZhhVgnhiZel]ZchfjVg^c\
Vldg`e^ZXZ[dgVi]^X`cZhheaVcZg#
NOTICE
If you are not experienced with a jointer,
set the depth of cut to 0" and practice
feeding the workpiece across the tables as
described for each of the jointing proce-
dures. This process will better prepare you
for the actual operation.
Figure 25.:mVbeaZd[hjg[VXZeaVc^c\l^i]i]Z
_d^ciZg#
Figure 26.>aajhigVi^dcd[hjg[VXZeaVc^c\gZhjaih#
To surface plane the workpiece on the joint-
er:
1. 9>H8DCC:8I?D>CI:G;GDBEDL:G
2. BV`Z hjgZ ndj gZVY VcY [daadl i]Z Safety
Instructions WZ\^cc^c\ dc Page 6 VcY i]Z
Stock Inspection & Requirement gjaZh
WZ\^cc^c\dcPage 21#
3. KZg^[ni]Vii]Zdji[ZZYiVWaZ]Z^\]i^hegdeZgan
hZi gZ[Zg idSetting Outfeed Table Height
dcPage 33[dgYZiV^aZY^chigjXi^dch#
4. HZi i]ZYZei] d[ Xji [dg ndjg deZgVi^dc VcY
i]Z[ZcXZid.%#
Note: We suggest a
1
32" depth of cut for sur-
face planing, and a more shallow depth for
hardwood species or for wide stock.
5. >[ndjgldg`e^ZXZ^hXjeeZYdglVgeZY!eaVXZ
^i hd i]Z XdcXVkZ h^YZ ^h [VXZ Ydlc dc i]Z
^c[ZZYiVWaZ#
6. 8dccZXii]Z_d^ciZgidedlZgVcYijgc^iON#
Failure to use push blocks when surface
planing could result in your hands contact-
ing the rotating cutterhead, which will cause
serious personal injury. ALWAYS use push
blocks when surface planing on the jointer!
7. L^i] V ejh] WadX` ^c ZVX] ]VcY! egZhh
i]Z ldg`e^ZXZ V\V^chi i]Z ^c[ZZY iVWaZ VcY
i]Z [ZcXZ l^i] [^gb egZhhjgZ! i]Zc [ZZY i]Z
ldg`e^ZXZdkZgi]ZXjiiZg]ZVY#
Note: When your leading hand comes within
4" of the cutterhead, lift that push block up
and place it on the workpiece portion that is
on the outfeed table. Now, focus the down-
ward pressure with the leading hand while
feeding, then repeat the same action with
your trailing hand when it comes within 4" of
the cutterhead. Keep your hands safe! DO
NOT allow them to get any closer than 4"
from the cutterhead.
8. GZeZViStep 7jci^ai]ZZci^gZldg`e^ZXZhjg"
[VXZ^h[aVi#