Haier HL26R1 Flat Panel Television User Manual


 
Operation
Remote Control
Setting Up Your Remote Control
After it has been set up properly, your remote control can operate in six different modes:
TV, DVD, VCR, SETBOX, CABLE orAUDIO. Pressing the corresponding button on the remote control
allows you to switch between these modes, and control whichever piece of equipment you choose.
Note
The remote control might not becompatibte with altDVD Players, VCRsand Cable boxes.
Remote Operation
To control a deviceusing the Remote
1. Program theRemote to workwith your device.
2. Changing devicemode by pressingSELECT key. Default device isTV. When press
SELECT key, current device ledwill be on. Keep pressing SELECT key to choosea
device, theloopis:TV DVD VCR STB Cable Audio-TV. When device is set, related
device LED willbe on for5 seconds andthen be off:.
3. Aimthe remote atthe device.
4. Press POWER button to turnthe device on.
5. Use theother Remote buttonsto operate thedevice. Device LEDwill blink ifuser presses
any key (ifthe key hasdata in currentmode.). If thekey has nodata, then LEDwill not blink.
6. Default initstatus: TV/Haier001 code.
7. Bulb keyto control theflash light.
Programming the Remote
The Remote isfactory-programmed to supportup to 600code sets.
There are twoways to programthe Remote:
Selecting a brandcode for thedevice you wishto operate, andthen entering thatcode
manually into the Remote.
Using the PowerScan feature tofind device codesautomatically.
The two programming methods are described in the following sections.
Manually Programming theRemote
1. Using SELECT key to choosethe device youwant to program.
2. While Pressand holding ENTER key, press SELECT key, and device LEDwill be ON. Keep
the status forabout 5 seconds,release both keysand then LEDwill blink twiceper second,
indicating that the Remote is readyfor programming.
3. Led will blink once when you enter a digit key, indicating the digit key is programmed. If 3
digits are programmed successfully, device LED will be ON forabout 3 seconds and then
blink twice persecond. Then User now can:
a.Try to operate the device by using POWER or PLAY keys. If operation can be done,
press ENTER to save current3-digits code and exiting manually programming mode.
b.Return to beginning of step 3.Reprogram the Remote.
4. If user'sinput is incorrect, LED will blink 12 times in 3 seconds.And then keeptwice per
second blink, usernow can returnto step 3and re-program thedevice.
5. Within 10seconds, user shouldenter the 3-digitbrand code corresponding to your device.
If time outor any keyother than POWER, PLAYanddigitsispressed, LEDwillbeoffand
manually programming processis exit.
6. Fast Programming Haier default TV code set. Press and holding EXIT key and then press
SELECT key for 5seconds, default Haiercode set (001)will be programmed to the Remote.
Manually scan mode
With manually scan programming, the control tests all the codes available in the code setdata
base and assignthe correct onefor the selecteddevice.
To manually-scan program the Remote:
1. Manually turnOFF the devicefor manually scan mode. (TV, DVD, VCR, STB, cable boxor
audio equipment).
2. Press SELECT key to choosethe device youwish to program.
While Press andholding ENTER key, press SELECT key and device LED will beON. Keep
the status forabout 5 seconds,release both keysand then LEDwill blink twiceper second,
indicating that thecontrol is readyfor programming.
3. Press and release CH+/CH- key. The LED blinks 10 timesper seconds, indicatingthat
the Remote isin manually scanmode.
4. Press CH+/CH-key repeatedly until the device switches ON (CH+ key conducts aupward
search while CH- key conducts adownward search in the code set database).
34 TV LCD-TFT