Hitachi 53F300 Projection Television User Manual


 
VCR BRAND CODE
Aiwa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Daewoo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Emerson. . . . . . . . . . . . . . . . . . . 20,21,22,23,24
Fisher . . . . . . . . . . . . . . . . . . . . . . . 34,37,38,39
Funai. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
General Electric. . . . . . . . . . . . . . . . . . . . . . . 33
Goldstar . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Hitachi . . . . . . . . . . . . . . . 00,01,02,03,04,05,06
JVC. . . . . . . . . . . . . . . . . . . . . . . . . 18,49,50,51
Magnavox . . . . . . . . . . . . . . . . . . . . . . 12,13, 14
Mitsubishi . . . . . . . . . . . . . . . . . . . . 27,28,29,30
NEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40,41
VCR BRAND CODE
Panasonic. . . . . . . . . . . . . . . . . . . . . . . . . 10,11
Philips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Samsung . . . . . . . . . . . . . . . . . . . . . . . 17,25,26
Scott . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Sharp . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31,32
Shintom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Sony . . . . . . . . . . . . . . . . . . . . . . . . . . 07,08,09
Symphonic . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Teknica . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Toshiba . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
MY VCR CODE IS:
THE REMOTE CONTROL
27
USING THE REMOTE TO CONTROL VCR FUNCTIONS
Operating the precoded function for your VCR.
This remote is designed to operate different types of VCRs. You must first program the remote to match the remote system of your VCR
(refer to table below for pre-codes).
1. Turn ON your VCR.
2. Aim the remote control at the front of your VCR.
3. Press and release the DVD/VCR button to switch to VCR pre-coded mode.
4. Hold down the DVD/VCR button on the remote and enter the two digit preset code that matches your VCR, as shown below.
5. Aim the remote at the VCR and press the POWER button. The remote will turn off your VCR when the correct two digit preset code
is entered. When this occurs, the remote control is programmed for your VCR. If the VCR does not turn off, try a different two digit
preset code.
6. The remote will now control your VCR.
NOTES:
1. If your VCR cannot be operated after performing the
above procedures, your VCR’s code has not been
precoded into the remote.
2. In the unlikely event that your VCR cannot be operated
after performing the above procedures, please consult
your VCR operating guide.
3. The remote control will remember the codes you have
programmed until the batteries are removed from the
remote control. After replacing the batteries repeat the
entire programming procedure as stated above.
DVD/VCR Button
This button allows the remote to control your VCR by setting
it to VCR mode.
PRECODED VCR Buttons
These buttons transmit the chosen precoded VCR codes.
For some VCRs, you must press the RECORD button twice
to record a program.
EXCLUSIVE TV Buttons
These buttons are for operating the TV.
123
456
789
0
ANT
INFO
VOL CH
POWER
TV CBL/SAT DVD/VCR
PIP
SWAP PIP MODE
FREEZE
VIDEO
MENU
MUTE
EXIT
LAST CH
REC
ASPECT
VIRTUAL HD
SELECT
PIP CH
VID1
VID2
VID3 VID4
VID5
NOTE: Refer to instruction manual of the VCR for operation of the buttons exclusively for the VCR.