Filter
Top Products
PICTURE-IN-PICTURE (PIP)
29
NOTES: 1. Y-P
B
P
R
input cannot be viewed as main picture or sub-picture when in SINGLE PIP MODE. If you tune to a Y-P
B
P
R
input, the TV set will automatically change to SPLIT PIP MODE.
2. When ANT B is selected as the main channel, the SWAP feature is disabled.
3. COMPONENT: Y-P
B
P
R
input can be viewed as main or sub-picture, only when SPLIT PIP MODE is chosen.
4. Only sound from the main picture can be heard.
Main Picture
Sub Picture
ANT A 10
OUTPUT
STOP
CONNECT ONLY 8 OHM SPEAKERS
DO NOT SHORT CIRCUIT
THESE TERMINALS
(Such damage is NOT COVERED
by your television warranty)
P
B
P
R
P
B
P
R
L
REAR SPEAKER
8Ω ONLY
R
Hitachi Model or
Similar Model
Back of
VCR
V L R
Rear Panel of Television
VCR
MONITOR
OUT
INPUT 2
INPUT 1
AUDIO
(MONO)
L
R
AUDIO
L
R
S-VIDEOS-VIDEO
VIDEO
VIDEO
ANT A
TO
CONVERTER
ANT B
AUDIO
L
R
(MONO)
S-VIDEO
VIDEO
YY
AUDIO
TO HI-FI
R
L
SUB
WOOFER
OPTICAL
INPUT
COAXIAL
INPUT
PIP
Your HITACHI Projection TV incorporates Dual Tuner technology designed for improved viewing enjoyment. This Dual Tuner feature
allows you to view antenna inputs on both the main picture and sub-picture simultaneously, with separate tuning control for each. The
Dual Tuner can operate with only one input (ANT A only) or two inputs (ANT A and ANT B).
ANT A input can be viewed as both the main picture and the sub-picture simultaneously. ANT B can only be viewed as a main picture.
(Component: Y-P
B
P
R
input can be viewed as sub-picture only when SPLIT PIP mode is selected.) To select between main picture and
PIP sub-picture tuning, press the PIP CH button on the remote. The highlighted channel display will move with every press of the PIP
CH button. When the top channel display is highlighted, channel tuning is for the main picture. When the lower channel display is
highlighted, channel tuning is for the PIP sub-picture. This method of picture tuning is the same for one antenna input (ANT A only) and
two antenna inputs (ANT A and ANT B).
The Picture-in-Picture feature is convenient when you want to watch more than one program at the same time. You can watch a TV
program while viewing other programs from the ANT A source or any of the video inputs.
Use above connection to view VCR program as a sub-picture while viewing another program as main picture (ANT A, ANT B, V:2
or V:3 input). You may also view the VCR program as a main picture while viewing another program as a sub-picture (ANT A, V:2
or V:3 input).
ቢ PIP button
Press the PIP button and a sub-picture will appear in one of the three different modes (SINGLE, SPLIT or SURF), depending on
the last selection of the PIP mode. To change the PIP mode, use the PIP MODE button to cycle through the three different modes.
SINGLE MODE PIP
Press the PIP button and a sub-picture appears in one corner of the screen. Press the PIP button again to remove the sub-picture
from the screen. Use the PIP CH button to select between main and sub-picture tuning control (indicated by highlighted channel
display.) Press the INPUT button when sub-picture channel tuning is being controlled, to change between VIDEO: 1, VIDEO: 2,
VIDEO: 3, and ANT A antenna source. (ANT B source cannot be viewed as a sub-picture.)
SPLIT MODE PIP
When you press the PIP button, the main channel and the PIP sub-picture will appear at the center of the screen (main channel on left
side and sub-picture on right side). Press the PIP button a second time to return to normal viewing. Use the PIP CH button to select
between main and sub-picture tuning control (indicated by highlighted channel display). Press the INPUT button when sub-picture
channel tuning is being controlled, to change between VIDEO:1, VIDEO:2, VIDEO:3, and ANTA antenna source. (ANT B source cannot
be viewed as a sub-picture).
PIP
PIP
PIP
EXIT
MENU
CHVOL
RECALL
MUTE
GUIDE/TVGUIDE/TVGUIDE/TV
INFO
VCR PLUS+
SVCS
GUIDE/TV
SCHD
PIP PIP CH
SWAP
FREEZE
PIP MODE
PIP ACCESS
PROG
TV/VCR
SLOW
REC
SELECT
ብ,ቦ
ባ
ቤ
ቢ