7
ENGLISH
Remote control
PICTURE
SIZE
–/
9
1
2
3
4
5
6
7
8
10
12
11
13
14
15
16
4. SLEEP Button - To set the TV to turn off after a preset
amount of time, press the SLEEP button. The clock will
count up 10 minutes each time the button is pressed in
the order of 0h00m, 0h10m,...1h50m,2h00m After the sleep
time is programmed, the display will disappear then reappear
momentarily every ten minutes to remind you the sleep
timer function is operating. To confirm the sleep time setting,
press the SLEEP button once and the remaining time will
be momentarily displayed. To cancel sleep time, press the
SLEEP button repeatedly until the display turns to 0h00m.
5. VOL (VOLUME) + / - Buttons - Press the + button to
increase, or the - button to decrease the volume level.
Use to select the desired setting during the menu screen
operation.
6. MENU Button -
Press to display the menu screen function.
7. EXIT Button - Press remove the menu screen.
8. TV/AV Button -
Press this button to display SOURCE
SELECTION menu to select the video input source.
9. QUICK VIEW Button - This button allows you to go back
to the previous channel selected by pressing the
QUICK VIEW button. Press this button again to return to
the channel you were watching.
10. MUTE Button -
To turn off the sound, press this button once.
The TV will be silenced and the symbol “MUTE” will appear
on the screen. The muting feature can be released by
pressing the MUTE button again or one of the VOL
+ or - buttons.
11. CH (CHANNEL) / Buttons - Press the button to
change to a higher numbered channel set into memory.
Press the button to change to a lower numbered chan-
nel
set into memory.
Use to select the desired setting during the menu screen
operation.
12. ENTER Button - Press to enter or select information for
On-Screen operations while in the adjustment menu.
13. RESET Button - Press to reset the menu screen picture
and sound adjustments to their factory preset positions
while in the adjustment menu.
14.
CLOSED CAPTION Button - Press this button to display
CLOSED CAPTION menu.
15. AUDIO SELECT Button - Press this button to display
AUDIO menu.
16. PICTURE SIZE Button - Press this button to change
the picture size.
1. POWER Button - Press to turn the TV on. Press again to
turn the TV off.
2. Direct Channel Selection Buttons (0-9) - Allow direct
access to any channel.
3. -/DISPLAY Button - When the TV is receiving an analog
signal pressing this button will display the current infor-
mation on-screen. When the TV is receiving a digital,
pressing this button once will display the digital informa-
tion on-screen; pressing it a second time will display the
analog information on-screen. To remove the display
from the screen, press this button again. This button is
also the “-“ button used when selecting digital channels.
1. Open the battery compartment cover.
2. Install two “AAA” batteries.
HOW TO INSTALL BATTERIES
Before using the remote control, batteries must first be installed.
3. Replace the battery compartment cover.
BATTERY PRECAUTIONS
These precautions should be followed when using batteries
in this device:
• Use only the size and type of batteries specified.
• Be sure to follow the correct polarity when installing the
batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g.
Alkaline and Carbon-zinc) or old batteries with fresh ones.
• If the device is not to be used for a long period of time,
remove the batteries to prevent damage or injury from
possible battery leakage.
•
Do not try to recharge batteries not intended to be recharged;
they can overheat and rupture (follow battery manufacturer's
directions).
Use two “AAA” size batteries. The batteries may last
approximately one year depending on how much the remote
control is used. For best performance, it is recommended
that batteries should be replaced on a yearly basis, or when
the remote operation becomes erratic. Do not mix old and
new batteries or different types.
J3W40621B_En_P02-09 15/02/2006, 10:43 AM7