Filter
Top Products
22
Insignia NS-LCD26A LCD TV
www.insignia-products.com
Specifications
Programming the remote
control
Introduction
Your remote lets you control four devices with
one easy-to-use, compact unit. After installing
batteries, you can program the remote to control
your VCR or DVD, cable or satellite receivers,
amplifier or tuner, and auxiliary devices. To do
so, follow the instructions in “Programming a
Device” For best results, please read and follow
all the remaining instructions. Keep this guide for
future reference.
Programming a device
To control a VCR or DVD, cable or satellite
receiver, amplifier or tuner, and auxiliary device,
follow these steps. Before proceeding, find the
codes for the devices you want to program in the
following tables and write them down or highlight
them.
To program a device:
1 Turn on the device (for example, the DVD
player) and, if needed, load the media (for
example, a DVD).
2 Press the DVD, CBL, or AUX button.
3 Press and hold SET until the red LED blinks
twice, then release the button.
4 Enter the first five-digit code for your device.
The LED blinks once as each digit is entered.
If the code is correct, the LED blinks twice.
5 Aim the remote at the device and press
Power. The device should turn off. If it does
not, repeat steps 3 to 5, trying each code for
your brand until you find one that works. If
you cannot find a code that works, see
“Searching for Your Code”
General One or more
channels can't
be displayed
• These channels may be
locked. Use the parental
controls to unlock them.
• These channels may be set
to Not Viewable in the
channel list. Set the channel
to Viewable or select the
channel with the 0-9 number
buttons.
Lost password • Use the super password
(1397) to access the
Password Set menu and set
a new password as desired.
Write down your new
password.
Some items
can't be
accessed
• If a setting option appears in
gray, this indicates that the
settings option is unavailable
in current input mode.
Television
cabinet creaks
• When the television is in use,
there is a natural rise in
temperature, causing the
cabinet to expand or contract
and may be accompanied by
a slight creaking noise. This
is not a malfunction.
Control buttons
do not operate
• Disconnect the power cord
and wait for a few seconds.
Then re-connect the power
cord and turn on the
television again.
Caution
Never attempt to repair a defective television
yourself.
Note
If your problem is not solved, turn your television
off and then on again.
Note
• Design and specifications are subject to
change without notice.
• Weight and dimensions shown are
approximate.
• Specifications and external appearance may
be changed for the sake of improvement.
Type LCD TV
TV system American TV standard ATSC/NTSC system
Receiving channels VHF 2-13, UHF 14-69, CATV 1-125, CADTV
1-135, DTV 2-69
Audio multiplex BTSC system
Audio out 6W x 2
Power requirement AC 120 V. 60 Hz
Power
consumption
120 W
Dimensions 27 x 21.8 x 9.1-inches
(685 x 553 x 231 mm)
Weight 42 lbs/19 kg
Category Problem Possible Solution
Input terminals 2 Composite Video/Audio (L/R)
1 S-video
2 Component Video/Audio (L/R)
2 HDMI interface
1 VGA/Audio
1 Antenna
Output terminals 1 Composite Video/Audio (L/R)
1 S/PDIF optical digital audio out
1 headphone jack
Control terminals 1 RS-232
Note
The universal remote control unit can't be
programmed to control a different brand of
television. It has been preset to control this
television set and this preset is unchangeable.
Note
To program a DVD player, portable DVD player, or
mobile DVD player, use the DVD key.
Note
If the LED does not blink twice, repeat steps 2 to 4
and try entering the code again.