Filter
Top Products
12
Before You Start
EN
Installing Batteries in the
Remote Control
Install two R6 (AA) batteries (supplied) into the
remote control, carefully match with the polarity
indicated inside the battery compartment.
Caution
• Incorrect use of batteries can result in hazards such
as leakage and bursting.
• Do not mix new and old batteries together.
• Do not use different kinds of batteries together.
• Make sure that the plus and minus ends of each
battery match the indications inside the battery
compartment.
• Remove batteries if the equipment will not be used
for a month or more.
• When disposing used batteries, please comply with
governmental regulations or the public instructions
for environmental protection that apply in your
country or area.
• Do not recharge, short-circuit, heat, burn or
disassemble batteries.
About the Remote Control
• Make sure there is no obstacle between the remote
control and the remote control sensor on the unit.
• Use within the operating range and angle as shown.
• Remote control operation may become unreliable if
the remote control sensor of the unit is being
exposed by the strong sunlight or fluorescent light.
• Remote controls for different devices can interfere
with each other. Be careful when using remote
controls for other equipment located close to the
unit.
• Replace the batteries when the operating range of
the remote control reduces.
VCR / DVD Recorder Switching
Because this product is a combination of a VCR and a
DVD recorder, you must select first which component
you wish to operate with [VCR/DVD] on the front
panel.
Press [VCR] on the remote control.
(Verify that the VCR light is lit.)
Press [DVD] on the remote control.
(Verify that the DVD light is lit.)
Note
• Pressing only [VCR/DVD] on the front panel DOES
NOT switch the mode of the remote control. You
MUST select the correct mode on the remote
control.
•Press [VCR/DVD] to select the DVD mode or the
VCR mode.
• You cannot switch to the mode (DVD or VCR) that is
in the timer-standby mode.
• If the media is available, you can start recording by
pressing [DVD REC I] or [VCR REC I] on the
remote control even if another equipment (DVD or
VCR) is selected. In this case, the mode of the
remote control will be automatically switched to the
appropriate component.
21
3
60˚
E
J
E
C
T
O
P
E
N
/
C
L
O
S
E
S
E
T
U
P
S
T
AN
DB
Y
/O
N
R
E
P
E
A
T
Z
O
O
M
P
R
R
E
T
U
R
N
M
E
N
U
/
L
I
S
T
T
O
P
M
E
N
U
C
L
E
A
R
AUDIO
P
L
A
Y
W
S
L
O
O
P
T
I
M
E
R
S
H
O
W
V
I
E
W
P
R
O
G
O
N
S
C
R
E
E
N
A
B
C
.@
/
:
D
E
F
J
K
L
G
H
I
M
N
O
T
U
V
P
Q
R
S
W
X
Y
Z
1
4
7
2
5
8
0
3
6
9
E
N
T
E
R
VC
RD
VD
S
T
A
N
D
B
Y
/
O
N
V
C
R
D
U
B
B
IN
G
P
R
V
C
R
/
D
V
D
S-VIDEO
VIDEO
(
M
O
N
O
)
L
-
AU
D
IO
-
R
D
V
D
V
C
R
D
V
D
Within about
5 m
Remote
control
Code (DVD): JVC C
Code (VHS): JVC A
VCR mode
DVD mode
STANDBY/ON
VCR
DUBBING
PR
VCR/DVD
S-VIDEOVIDEO
(MONO)
L
-
AUDIO
-
R
DVD
VCR DVD
VCR/DVD
VCR DVD
DVD light
VCR light
1_16_BeforeSrart_EN.fm Page 12 Monday, September 5, 2005 1:58 PM