Filter
Top Products
February 27, 2004 9:51 am Page 9
—9—
Master Page: Right
Up to 8 timer recording programmes can be made.
Before starting:
● Set the clock properly. (
੬
13)
● Set “COLOUR SYSTEM” to the appropriate mode. (
੬
12)
● Load a cassette with the record safety tab intact.
NOTES:
● PDC recording is not possible in Central and Eastern Europe.
● If all the 8 programmes have already been set, “PROGRAM
FULL” appears on the screen.
● If the clock is not set, “CLOCK MUST BE SET” appears on the
screen.
● After timer recording is completed, the recorder turns off
automatically.
● If the tape reaches its end during timer recordings, the recording
stops and “#”, “
⅜
” and “ $” on the display panel blink. Press
# to disengage timer, then press 0 on the recorder to eject
the cassette or press 1 then press 3 to rewind the tape.
● You can programme the timer recording while a regular
recording is in progress; the menu screens will not be recorded.
S
HOW
V
IEW
™
Timer Programming
The S
HOW
V
IEW
numbers are the numbers next to the programme
in most TV listing.
A
Press PROG to access the Timer Programming Set screen.
B
Press RT to place the pointer next to
“S
HOW
V
IEW
“, then press OK or . The
S
HOW
V
IEW
NO. screen appears.
C
Press the appropriate number keys to
input the S
HOW
V
IEW
number, then press
OK. The S
HOW
V
IEW
program screen
appears.
● If the number you entered is invalid,
“ERROR” appears on the screen. Press &
and input a valid S
HOW
V
IEW
number.
● Make sure the channel position number you wish to record is
displayed; if “TV PROG” displays “––”, set the channel position
number correctly. Press PR / to input the channel position
number on which your recorder receives the station. Then press
OK.
● To set the channel position number for
the satellite broadcast station, press
the number key “0” to change “TV
PROG” to “SAT”. Press PR / to
input the channel position number on
which your satellite receiver receives
that station. Then press OK.
● To set the tape speed, press p(SP/
LP).
● To set the VPS/PDC mode, press VPS/PDC (number key “7”).
● To change the stop time, press STOP / (number keys “2”
and/or “5”).
● To timer-record daily (Monday–Friday) or weekly serials, press
DAILY (number key “8”) or WEEKLY (number key “9”). Pressing
the button again makes the “DAILY” or “WEEKLY” display
disappear.
● To change the channel position number, press PR / .
D
Press OK or PROG.
● If “PROGRAM OVERLAPPED” appears, see “Program overlap
warning display” (
੬
10).
E
Press #. The recorder turns off automatically and “#” is
displayed on the display panel.
To timer-record a satellite broadcast using the SHOW
V
IEW
system:
A Perform “Satellite Receiver Control Set” (
੬
5).
B Perform steps 1
11
1 – 5
55
5. In step 3
33
3, you cannot set “VPS/PDC” to
“ON”.
C Leave the satellite receiver’s power on.
Express Timer Programming
A
Press PROG to access the Timer Programming Set screen.
B
Press RT to place the pointer (highlighted bar) next to
“EXPRESS PROGRAMMING”, then press OK or . The
program screen appears.
C
Press START / (number keys “1”
and/or “4”), STOP / (number keys “2”
and/or “5”), DATE / (number keys “3”
and/or “6”) or PR / repeatedly to enter
the start time, stop time, date or channel.
● Press and hold START / or STOP
/ to increase the time in 30-minute
intervals.
● To set the tape speed, press p(SP/LP).
● To set the VPS/PDC mode, press VPS/PDC (number key “7”).
● To timer-record daily (Monday–Friday) or weekly serials, press
DAILY (number key “8”) or WEEKLY (number key “9”). Pressing
the button again makes the “DAILY” or “WEEKLY” display
disappear.
D
Press OK or PROG.
● If “PROGRAM OVERLAPPED” appears, see “Program overlap
warning display” (
੬
10).
E
Press #. The recorder turns off automatically and “#” is
displayed on the display panel.
To timer-record a satellite broadcast using Express Timer
Programming:
A Perform “Satellite Receiver Control Set” (
੬
5).
B Perform steps 1
11
1 – 5
55
5. In step 3
33
3, press the number key “0” to
change “TV PROG” to “SAT”. Then press PR / to enter the
channel position for the satellite broadcast. You cannot set “VPS/
PDC” to “ON”.
C Leave the satellite receiver’s power on.
Timer Recording
MENU
AUDIO
VPS/PDC
START
STOP
DATE
WEEKLY
DAILY
AUX
0000
TV
/
VCR
PROGPROG
123
456
789
0
OK
PR
PR
30SEC
REC
HR-V610_001EN.fm Page 9 Friday, February 27, 2004 9:52 AM