JVC HR-S7950EU VCR User Manual


 
Masterpage:Right-NoTitle0
EN
41
Filename [HRS7950EU3-EN.fm]
Page 41 March 6, 2002 1:49 pm
Edit To Or From
Another Video
Recorder
You can use your recorder as the source player or as the
recording deck.
A
Make connections.
Connect the player’s 21-pin SCART connector to the
recorder’s 21-pin SCART connector as illustrated.
A
When using your recorder as the source player ...
... connect its AV1 (L-1) IN/OUT connector to the
recording deck.
B
When using your recorder as the recording deck ...
... connect its AV1 (L-1) IN/OUT or AV2 (L-2) IN/
DECODER connector to the source player.
If another recorder is compatible with the Y/C signal ...
... when using your recorder as the source player, set “L-1
OUTPUT” to “S-VIDEO” (
pg. 42).
... when using your recorder as the recording deck, set “L-2
INPUT” to “S-VIDEO” (
pg. 43).
B
Set the input mode of recording deck.
With this video recorder, press
AUX
(
number key
0
”)
and/or
PR
to select “L-1” for the AV1 (L-1) IN/OUT
connector, or “L-2” for the AV2 (L-2) IN/DECODER
connector, depending on the connector being used.
When using another recorder as the recording deck, refer to its
instruction manual.
When using the AV2 (L-2) IN/DECODER connector, set “L-2
SELECT” to “A/V” (
pg. 43).
C
Set the edit mode.
See “PICTURE CONTROL” on page 49.
D
Start the source player.
Engage the Play mode of the source player.
E
Start the recording deck.
Engage the Record mode of the recording deck.
NOTES:
All necessary cables can be obtained from your dealer.
For Y/C signal input/output, be sure to use a 21-pin SCART
cable that is compatible with the Y/C signal.
When you select “EDIT” to dub tapes in step
3
, be sure to
select “AUTO” (or “NORM” when “B.E.S.T.” is set to “OFF”)
after you finish dubbing the tapes.
When you use this recorder as the source player for editing, be
sure to set “O.S.D.” to “OFF” before starting (
pg. 49).
If you are using another recorder with S-Video and Audio
input/output connectors, you can connect those connectors to
this recorder’s S-VIDEO and AUDIO input/output connectors.
When using your recorder as the source player ...
... connect its rear panel S VIDEO OUT and AUDIO OUT
connectors to the recording deck’s S-Video and Audio input
connectors.
When using your recorder as the recording deck ...
... connect its front panel S-VIDEO and AUDIO input
connectors to the source player’s S-Video and Audio output
connectors. Then, set the recorder’s input mode to “S-1”.
Advantages of S-VHS video recorders
You can edit from VHS to S-VHS, S-VHS to VHS, or, from
S-VHS to S-VHS.
From VHS to S-VHS: Record VHS playback signals in the
S-VHS mode. Although the picture quality is inherently
limited by that of the original, the edited tape has better
picture quality than those made by VHS-to-VHS editing.
From S-VHS to VHS: Because the picture quality of the
source material is very high, the edited tape has better
picture quality than those made by VHS-to-VHS editing.
From S-VHS to S-VHS: All signals will be transferred with
minimum degradation.
A
B
AV mode
21-pin SCART cable
(not provided)
Recorder
Your recorder
Another recorder
Player
TV receiver
AV mode
21-pin SCART cable
(not provided)
Recorder
Your recorder
Another recorder
Player
TV receiver
HRS7950EU1-EN.book Page 41 Wednesday, March 6, 2002 1:49 PM