Filter
Top Products
Masterpage:Left-FullCol
70
EN
Filename [HRS9850EU4.fm]
Page 70 May 21, 2001 1:37 pm
SUBSIDIARY SETTINGS (cont.)
* The default setting is
bold
in the table below.
8
DIRECT REC
ON
OFF
When this function is set to “ON”, you can easily start recording the
programme that you are watching on your TV. Press and hold
7
and press
4
on
the remote control, or press
7
on the recorder.
NOTES:
●
When you use the Direct Rec function, be sure to use a TV offering T-V LINK, etc. and
connect a fully-wired 21-pin SCART cable between the recorder and the TV
(
੬
pg. 10).
●
If “DIRECT REC” is set to “OFF”, the
7
button functions as described in “Basic
Recording” (
੬
pg. 24).
●
During the Direct Rec, “– –” appears on the front display panel.
●
If a programme is recorded with the Direct Rec, the station name will not be registered
for the Video Navigation. “– – – –” will be displayed for the station name.
●
Retake function (
੬
pg. 26) does not work during Direct Rec.
8
AUTO SP
]
LP TIMER
ON
OFF
When this function is set to “ON”, the recorder automatically switches to LP
mode to allow complete recording if there is not enough tape to record the
entire programme while timer-recording in SP mode.
For Example . . .
Recording a programme of 210 minutes in length onto a 180-minute tape
Make sure you set this function to “ON”, before the timer-recording starts.
NOTES:
●
If you have programmed the recorder to timer-record 2 or more programmes, the
second programme and those thereafter may not fit on the tape if you set “AUTO
SP
]
LP TIMER” to “ON”. In this case, make sure the mode is not engaged, then set the
tape speed manually during timer programming.
●
In order to ensure that the recording fits on the tape, this feature may leave a slight
non-recorded section at the end of the tape.
●
There may be some noise and sound disturbance at the point on the tape where the
recorder switches from SP to LP mode.
●
The Auto SP
]
LP Timer feature is not available during ITR (Instant Timer Recording),
and the feature will not work properly with any tapes longer than E-180, or with some
tapes of shorter lengths.
●
If you perform timer recording with both VPS/PDC and the Auto SP
]
LP Timer
activated, and the programme goes beyond its originally scheduled length, there may
be times when the programme cannot be recorded in its entirety.
8
DIGITAL 3R
ON
OFF
When this function is set to “ON”, the Digital 3R picture system applies edge
correction to the luminance signal to enhance detail.
NOTES:
●
Normally it is recommended to keep “DIGITAL 3R” set to “ON”.
●
Depending on the type of tape being used, picture quality may be better with “DIGITAL
3R” set to “OFF”.
●
If you use the recorder as the source player for editing, be sure to set “DIGITAL 3R” to
“OFF” before starting.
8
POWER SAVE
ON
OFF
When this function is set to “ON”, you can reduce the power consumption
while the recorder is turned off.
NOTES:
●
During Power Save mode ...
... the front display panel will be turned off.
... the Just Clock function (
੬
pg. 80) does not work.
... the picture may be distorted momentarily when you turn on/off the recorder.
●
Power Save does not work when ...
... the recorder is in the Timer mode.
... the recorder’s power is turned off after timer-recording or Instant Timer Recording.
... the Automatic Satellite Programme Recording mode is engaged (
੬
pg. 38).
... “L-2 SELECT” is set to “DECODER” or “SAT” (
੬
pg. 53).
Total 210 minutes
Approximately 150 minutes Approximately 60 minutes
SP mode LP mode
HRS9850EU1.book Page 70 Monday, May 21, 2001 1:44 PM