Filter
Top Products
EN 37
ACCESS MAIN MENU
SCREEN
1
Press MENU.
ACCESS FUNCTION SET
SCREEN
2
Move the highlight bar (arrow) to "FUNCTION SET" by
pressing CH
5
∞ or SHUTTLE PLUS
%
fi, then press OK
or SHUTTLE PLUS .
SELECT AUTO TIMER SET
MODE
3
Move the highlight bar (arrow) to "AUTO TIMER" by
pressing CH
5
∞
or SHUTTLE PLUS
%
fi
, then press OK
or SHUTTLE PLUS to set to "ON" or "OFF".
RETURN TO NORMAL
SCREEN
4
Press MENU.
Auto Timer
When the Auto Timer is set to “ON” the timer is automatically
engaged when the VCR's power is turned off. It is automatically
disengaged when the VCR is powered back on.
Auto SP
→
EP Timer
If, when recording in SP mode, there is not enough tape to record
the entire program, the VCR automatically switches to EP mode
to allow complete recording. This feature is especially handy
when recording a program of more than 2 hours in length.
For Example . . .
Recording a program of 140 minutes in length onto a 120-
minute tape
Make sure you set "AUTO SP→EP TIMER" to “ON” at the
Function screen before the timer recording starts.
Approximately 110 minutes
SP mode
Approximately 30 minutes
EP mode
Total 140 minutes
%
%
NOTES:
●
If you have programmed the VCR to timer-record 2 or more
programs, the second program and those thereafter may not
fit on the tape though you set the Auto SP
→
EP Timer mode to
"ON". In this case, make sure the mode is not engaged, then
set the tape speed manually during timer programming.
●
In order to ensure that the recording fits on the tape, this
feature may leave a slight non-recorded section at the end of
the tape.
●
There may be some noise at the point on the tape where the
VCR switches from SP to EP mode.
●
The Auto SP
→
EP Timer feature is not available during ITR
(Instant Timer Recording), and the feature will work with the
following tapes: T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120.
FUNCTION
VIDEO CALIBRATION ON
PICTURE CONTROL AUTO
AUTO TIMER OFF
SUPERIMPOSE ON
= AUTO SP
=EP TIMER ON
VIDEO STABILIZER OFF
SELECT WITH (5,∞) AND (OK)
PRESS (MENU) TO END
HR-VP473U
FUNCTION
VIDEO CALIBRATION ON
PICTURE CONTROL AUTO
AUTO TIMER OFF
SUPERIMPOSE ON
= AUTO SP
=EP TIMER ON
NEXT PAGE
SELECT WITH (5,∞) AND (OK)
PRESS (MENU) TO END
HR-VP673U
HR-VP673U HR-VP473U
FUNCTION
VIDEO CALIBRATION ON
PICTURE CONTROL AUTO
=AUTO TIMER OFF
SUPERIMPOSE ON
AUTO SP
=EP TIMER ON
NEXT PAGE
SELECT WITH (5,∞) AND (OK)
PRESS (MENU) TO END
FUNCTION
VIDEO CALIBRATION ON
PICTURE CONTROL AUTO
=AUTO TIMER OFF
SUPERIMPOSE ON
AUTO SP
=EP TIMER ON
VIDEO STABILIZER OFF
SELECT WITH (5,∞) AND (OK)
PRESS (MENU) TO END
NOTE:
For safety, when AUTO TIMER is set to “OFF”, all other VCR
functions are disabled while the Timer mode is engaged. To
disengage the timer, press TIMER.
ACCESS MAIN MENU
SCREEN
1
Press MENU.
ACCESS FUNCTION SET
SCREEN
2
Move the highlight bar (arrow) to "FUNCTION SET" by
pressing CH
5
∞ or SHUTTLE PLUS
%
fi, then press OK
or SHUTTLE PLUS .
SELECT AUTO SP
→
EP
TIMER SET MODE
3
Move the highlight bar (arrow) to "AUTO SP→EP
TIMER" by pressing CH
5
∞ or SHUTTLE PLUS
%
fi,
then press OK or SHUTTLE PLUS to set to "ON".
RETURN TO NORMAL
SCREEN
4
Press MENU.
%
%