Filter
Top Products
21
Changing the Aspect Ratio
The setting adjusted applies to all inputs.
• You can change the aspect ratio by pressing ASPECT. (See
page 15.)
1
Press MENU/EXIT (or MENU on the
Monitor) to display the Main Menu.
2
Press 5/∞ to move the cursor (3) to
“FUNCTION SELECT.”
3
Press 3 to display the Function
Selection Menu.
*
1
“SIGNAL MODE” appears only when VIDEO A,
VIDEO B, or COMPONENT input is selected.
*
2
“RGB/COMPO.” appears only when the RGB
B or COMPONENT input is selected.
*
3
“SYNC TERM.” appears only when the RGB B
input is selected.
4
Press 5/∞ to move the cursor (3) to
“ASPECT.”
5
Press 2/3 to select an aspect ratio you
want.
Each time you press the button, the aspect ratio changes
as follows:
* For detailed information on these aspect ratios, see
page 15.
6
Press MENU/EXIT (or MENU on the
Monitor) twice to exit from the menu
operations.
Note:
• When one of the following signals is being input, you
cannot select the aspect ratio you want.
■ 1080/50i, 1080/60i, 1035/60i or 720/60p signal through the
COMPONENT/RGB B input terminals
Aspect ratio is fixed to FULL (“ASPECT” will not appear
on the display).
■ When any signal other than RGB15K-60 and RGB15K-50
through the RGB A or COMPONENT/RGB B input terminals
You can select only REGULAR and FULL.
Cursor (3)
PICTURE ADJ.
SIZE/POSITION ADJ.
FUNCTION SELECT
STATUS DISPLAY
ENTER:
MAIN MENU
SELECT:
EXIT:
MENU
REGULAR FULL
ZOOMPANORAMIC
COLOR TEMP.
ASPECT
SIGNAL MODE
RGB/COMPO.
SYNC TERM.
reset
FUNCTION SELECT
ADJUST:
SELECT:
EXIT:
MENU
: HIGH
: PANORAMIC
: AUTO
: RGB
: HIGH
*
*1 *2 *3
Setting the Receivable Signal Types
You can set the receivable signal types. Normally, select
“AUTO.”
A common setting will apply to both the VIDEO A input and
the VIDEO B input, and a different setting will apply to the
COMPONENT input.
1
Press MENU/EXIT (or MENU on the
Monitor) to display the Main Menu.
2
Press 5/∞ to move the cursor (3) to
“FUNCTION SELECT.”
3
Press 3 to display the Function
Selection Menu.
*
1
“SIGNAL MODE” appears only when VIDEO A,
VIDEO B, or COMPONENT input is selected.
*
2
“RGB/COMPO.” appears only when the RGB
B or COMPONENT input is selected.
*
3
“SYNC TERM.” appears only when the RGB B
input is selected.
4
Press 5/∞ to move the cursor (3) to
“SIGNAL MODE.”
5
Press 2/3 to select the receivable video
signal type.
Each time you press the button, the receivable video
signal type changes as follows:
• When VIDEO A or VIDEO B input is selected:
•
When COMPONENT input is selected:
* Changes according to the “HD SIGNAL MODE”
setting (see page 27).
6
Press MENU/EXIT (or MENU on the
Monitor) twice to exit the menu
operations.
PICTURE ADJ.
SIZE/POSITION ADJ.
FUNCTION SELECT
STATUS DISPLAY
ENTER:
MAIN MENU
SELECT:
EXIT:
MENU
Cursor (3)
AUTO 480i 576i
480p720p
1080i
(1035i)*
COLOR TEMP.
ASPECT
SIGNAL MODE
RGB/COMPO.
SYNC TERM.
reset
FUNCTION SELECT
ADJUST:
SELECT:
EXIT:
MENU
: HIGH
: PANORAMIC
: AUTO
: RGB
: HIGH
*
*1 *2 *3
AUTO NTSC
PAL N PAL M
14_23_GM_V42[US] 03.6.26, 4:52 PM21