Filter
Top Products
Masterpage:Right+
EN 25
Filename [SR-MV50U_06DVD Operation1.fm]
Page 25 November 22, 2004 1:03 pm
OPERATIONS ON DVD DECK
Still Picture/Frame-By-Frame Playback
1 Press 9 to pause during playback.
2 Press 9 or we to activate frame-by-frame playback.
● Each press of 9 advances the still picture frame by frame.
● Each press of we advances/reverses the still picture frame by
frame.
● Frame-by-frame playback for reverse direction cannot be performed
with Video CD discs.
● To resume normal playback, press 4.
Slow Motion
1 Press 9 to pause during playback.
2 Press SLOW – (3) or SLOW + (5).
● Each press of SLOW – (3) or SLOW + (5) increases the slow
motion speed for each direction (from 1/16 to 1/2 times the normal
speed).
● Slow motion for reverse direction cannot be performed with Video CD
discs.
OR
Press SLOW – (3) or SLOW + (5) for 2 or more seconds.
Skip Search
During playback, press .
● Each press initiates an approximately 30-second period of fast-
motion playback. Normal playback resumes automatically.
Resume Function
It is possible to memorize the position where you stop playback
and resume playback from that position.
● Be sure to set “RESUME” to “ON” or “DISC RESUME”. (੬ pg. 70)
1 Press 8 during playback to memorize a resume point.
● The unit enters Resume Stop mode and memorize the position
where you have stopped playback as a resume point. (The inside of
the disc status indicator on the front display panel blinks while
memorizing.)
● The unit retains a memory of the resume points of the last 30 discs
played back, even though they have been ejected if “RESUME” is set
to “DISC RESUME”. (
੬ pg. 70)
● To clear the resume points:
(The inside of the disc status indicator stops blinking and lights.)
When “RESUME” is set to “ON”:
• Press 1 to turn off the unit.
• Press x (OPEN/CLOSE) to take out the disc.
• Press 8 in stop mode.
• Press TOP MENU to display the top menu, then start playback by
selecting an item, etc.
• Press MENU to display the disc menu, then start playback by selecting
an item, etc.
When “RESUME” is set to “DISC RESUME”:
• Set “RESUME” to “OFF”. (੬ pg. 70)
• Press 8 in stop mode.
• Press TOP MENU to display the top menu, then start playback by
selecting an item, etc.
• Press MENU to display the disc menu, then start playback by selecting
an item, etc.
2 Press 4 in stop mode to resume playback. The unit starts
playback from the resume point.
NOTES:
● “DISC RESUME” setting works on DVD VIDEO, VCD and already
finalized DVD-R/DVD-RW (video mode) discs. For other types of
discs, the function under “ON” setting will be applied even if
“RESUME” is set to “DISC RESUME”. (੬ pg. 70)
● If you stop the playback of a disc for which an resume point has
already been memorized, the memory will be updated with the new
resume point.
● After the unit has memorized the resume point for 30 discs,
remembering a new resume point will cause the unit to delete the
oldest memorized point. Stopping playback of a disc for which a
resume point is already stored may change the order in which the
points are stored. This may potentially change the order in which
points are deleted.
● When the unit memorizes a resume point for a disc, it also
remembers audio language, subtitle and angle settings.
● This function may not work for some Video CD.
● When “RESUME” is changed to “ON” or “OFF” (੬ pg. 70), resume
points of the discs memorized with “RESUME” set to “DISC
RESUME” will be cleared.
● Resume points are memorized for each side of a double-sided disc.
Marking Positions To Play Back Again Later
It is possible to mark positions (up to 999 points) where you want
to play back once again later, and start playback from a marked
position. Marking onto DVD-RAM/RW (VR mode only) discs when
recording is helpful to locate a start point when you play back the
discs later.
To mark positions:
During playback, press MARK at
positions you want to mark.
● “MARK” appears on the TV screen.
You can easily locate the marked
positions using 2 or 6 when you
play back the disc.
To delete the marked positions:
While paused, press 2 or 6 to
locate a marked position you want to
delete, then press MARK.
● Crossed “MARK” appears on the TV
screen, and the marked position is
deleted.
NOTES:
● When a monaural program changes to a stereo program while
recording, a mark signal is automatically recorded.
● When a DVD-R/RW (Video mode) disc is finalized, marked points
marked before finalizing will be deleted, and programs will be divided
automatically into “chapters” approximately every 5 minutes.
(੬ pg. 76)
SR-MV50US.book Page 25 Monday, November 22, 2004 1:03 PM