34 EN
REMOTE CONTROL
1 PROG. Button (੬ pg. 22)
2 TV Button (See below)
3 DISPLAY Button (੬ pg. 16)
4 TV/VCR Button (੬ pg. 13, 19)
5 Recording Speed [SP/EP] Button (੬ pg. 13)
6 ENTER Button (੬ pg. 13)
On-Screen Display [OSD] Button (੬ pg. 18)
7 CANCEL Button (੬ pg. 24)
Counter [C.] RESET Button (੬ pg. 16)
8 START +/– Button (੬ pg. 22)
9 STOP +/– Button (੬ pg. 22)
0 Rewind [REW] Button (੬ pg. 12)
! PLAY Button (੬ pg. 12)
@ Record [REC] Button (੬ pg. 13)
# MENU Button (੬ pg. 7)
$ OK Button (੬ pg. 6)
% PROG. CHECK Button (੬ pg. 24)
^ POWER Button (੬ pg. 6)
& NUMBER Buttons (੬ pg. 11, 13)
* DAILY Timer Recording Button (੬ pg. 23)
( WEEKLY Timer Recording Button (੬ pg. 23)
) "AUX" Mode Select Button (੬ pg. 28)
q TIMER Button (੬ pg. 23)
w Channel [CH] 5∞ Button (੬ pg. 6, 13, 22)
e DATE +/– Button (੬ pg. 22)
r Fast-Forward [FF] Button (੬ pg. 12)
t STOP Button (੬ pg. 12)
y PAUSE Button (੬ pg. 13)
u PUSH JOG %fi Button (੬ pg. 6)
TV Channel [CH] +/– Button (See below)
i PUSH JOG ™£ ( ) Button
(੬ pg. 14, 15)
TV Volume [VOL] +/– Button (See below)
NOTES:
●
When inserting the batteries, be sure to insert in the
correct directions as indicated under the battery cover.
●
Depending on the type of JVC TV, there may be cases
where some or all functions cannot be operated using the
remote control.
●
If the remote control doesn't work properly, remove its
batteries, wait a short time, replace the batteries and then
try again.
PROG.
CHECK
PROG.
TV operation – Press and hold
TV button, then press POWER,
TV CH +/–, VOL +/–, TV/VCR
POWER
TV
12 3
45
0
AUX
6
78
DAILY 9WEEKLY
DISPLAY
TV/VCR
CANCEL
START
•• REW FF ••
PLAY
REC
MENU
OK
STOP
TV CH +
TV CH –
TV
+ VOL
TV
VOL –
PAUSE
STOP DATE CH
C.RESET OSD
ENTER
TIMER
1
2
4
3
PUSH JOG
*
t
3
4
5
7
6
8
0
!
@
#
$
%
y
r
1
2
9
^
&
w
e
(
)
q
u
i
%
fi
INDEX (cont.)
How To Use
The remote control can operate most of your VCR's
functions as well as basic functions of JVC TV sets. (See
below)
● Point the remote control toward the sensor window.
● The maximum operating distance of the remote control
is about 8 m.
Operating JVC TVs
To operate your TV, while holding down TV, press the
corresponding button: POWER, TV/VCR, TV CH +/–. TV
VOL +/– can be used without holding down TV.
Buttons with a small dot on the left side of the name can
also be used to operate your JVC TV while holding down
the TV button. ੬ "Operating JVC TVs" below.
This remote control transmits A code signals only; it is not
applicable to B code signals.