Filter
Top Products
Initial settings
60
Initial settings
2
Select the desired speaker(s) to be set using
CURSOR 5/∞.
• F.S P: Front speakers. the level is fixed to 0dB.
• C.SP: Center speaker
• R.SP:Rear speakers
• S.WOOFER: Sub-woofer
The setting range is between –6dB and +6dB in 1dB
steps.
3
Set the level using CURSOR 2/3.
• For the speaker(s) whose size is set to “None”, the Speaker
level and Delay cannot be set (“—”appears in the setting
field).
• However, when playing back a Dolby Digital disc, LFE
singal is output from SUBWOOFER output even if
S. WOOFER shows “—”, allowing to activate a sub-woofer
connected. In such case, adjust the output level using the
level control on the sub-woofer.
Delay
(available only when selecting EXPERT)
You can adjust the delay
time of each speakers.
1
Select [DELAY] using CURSOR 5/∞, then
press ENTER.
The color of “DELAY” changes.
2
Select the desired speaker(s) to be set using
CURSOR 5/∞.
• F.S P: Front speakers. the delay is fixed to 0mS.
• C.SP: Center speaker (selectable from 0 to –5mS
in 1mS units)
• R.SP: Rear speakers (selectable from 0mS,
–5mS, –10mS, and –15mS)
3
Set the delay time using CURSOR 2/3.
• Delay of S.WOOFER cannot be set.
Te s t to n e
(available only while setting LEVEL or
DELAY)
You can check the level
setting by monitoring the
test tone.
1
Select [TEST TONE] using CURSOR 5/∞,
then press ENTER.
The color of “TEST TONE” changes.
2
Select the desired speaker(s) using CURSOR
5/∞.
• F.S P:Front speakers
• C.SP: Center speaker
• R.SP: Rear speakers
After selecting the Test tone, if you do not move the
cursor, the test tone is output from each speaker
one by one.
In Test tone mode, if you move down from
“R.SP” position, the test tone continues to output
from the rear speakers as long as is any position
other than “F. S P ” and “C.SP”. Similarily, if you
move up from “F. S P ” position, the test tone
continues to output from the front speakers as long
as is any position other than “C.SP” and “R.SP”.
3
Set the level using CURSOR 2/3 again, if
necessary.
• In Test tone mode, you hear pink noise, which includes all
frequencies in the audible range, from the speakers. This is
not a malfunction.
• The test tone is not output from the SUBWOOFER output.
NOTE
• To exit the speaker level (or delay) setting mode
Move
to [LEVEL] (or [DELAY]) in the on-screen display
and press ENTER until [LEVEL] (or [DELAY]) returns to
its original color.
SPK.SETTING
EXPERT
LEVEL
DELAY
TEST TONE
F. SP
0mS
C. SP
0mS
R. SP
0mS
0mS
S.WOOFER
PREFERENCE2PREFERENCE1
PRESS KEY
BASS
NOTE
• To exit the test tone mode
Move to [TEST TONE] in the on-screen display and
press ENTER until [TEST TONE] returns to its original
color.
SPK.SETTING
EXPERT
LEVEL
DELAY
TEST TONE
F. SP
0dB
C. SP
0dB
R. SP
0dB
0dB
S.WOOFER
PREFERENCE2PREFERENCE1
PRESS KEY
BASS
6$(1*ERRN3DJH0RQGD\-XQH30