Filter
Top Products
Operation
Control Operation
1.Program the Controller to work with your device.
2.Changing device mode by pressing the TV DVD
STB CABLE VCR AUD key. When device is set,
related device LED will be on for 1 second and then be
off.
3. Aim the remote at the device.
4. Use the other Controller buttons to operate the device.
Device LED will blink if user presses any key (if the key
has data in current mode.). If the key has no data, then
LED will not blink.
5. Default init status: TV/Haier codeset.
Manually Programming the Control
Check the code no. from the code list.
1. Choose the device you want to program.
2. While Press and holding ENTER key, press INPUT
key, and device LED will be ON. Keep the status for
about 3 seconds and the LED will blink, indicating
that the Controller is ready for programming, then
release both keys.
3.Led will blink once when you enter a digit key,
indicating the digit key is programmed. If 3 digits are
programmed successfully, device LED will be ON for
about 3 seconds and then blink twice per second.
Then User now can:
a)Try to operate the device by using power key.
B)If operation can be done, press ENTER key to save
current 3-digits code brand to EEPROM and exiting
manually programming mode.
C)Return to beginning of step 3. Reprogram the
control.
4. If user's input is incorrect, LED will blink 6 times in 3
seconds (2HZ). And then keep 2HZ blink, user now can
return to step 3 and re-program the device.
Within 30 seconds, user should enter the 3-digit brand
code corresponding to your device. If time out or any
key other than Power and digits is pressed, LED will be
off and manually programming process is exit.
Setting Up Your Remote Control
After it has been set up properly, your remote control can
operate in six different modes: TV, DVD, VCR, SETBOX ,
CABLE or AUDIO.
Note
The remote control might not be compatible with all DVD
Players, VCRs and Cable boxes.
Manually scan mode
With manually scan programming, the Controller tests
all the codes available in the codeset database and
assign the correct one for the selected device. Although
this method is more time consuming, it saves you the
trouble of looking up the brand codes necessary for
manual programming.
To manually-scan program the Controller:
1. Manually turn OFF the device for manually scan mode.
(TV, VCR, DVD, STB, cable box or audio equipment).
2. Choose the device you want to program.
3.While Press and holding ENTER key, press INPUT key,
and device LED will be ON. Keep the status for about 3
seconds and the LED will blink, indicating that the
Control is ready for programming, then release both
keys.
4.Press and release the CH+/CH- key.
The LED blinks with
10HZ freq, indicating that the Remote is in manually
scan mode.
5.Press CH+/CH- key repeatedly until the device
switches ON(CH+ key conducts a upward search while
the CH- key conducts a downward search in the code
set database). When the device turns ON, press and
release the ENTER key to program the Controller with
the new code, saving the code to EEPROM and exit.
6. After saving the new code, press POWER key. If the
device responds, no further programming is required.
If the device does not respond, repeat step 3 through 5.
And searching will start from current code set.
To exit without programming,
The code can not be saved to
EEPROM.
After searching the entire data base, this mode will be
automatically exited and led will blink for 3 times in 1.5
seconds. The code can not be saved to EEPROM.
Automatic Scan Programming the Controller
To automatic scan program the Controller:
1.Manually turn OFF the device you wish to power scan.
(TV, VCR, DVD,STB, cable box or audio equipment).
2. choose the device you wish to program.
3. While Press and holding ENTER key, press the INPUT
key and device LED will be ON. Keep the status for
about 3 seconds and the LED will blink, indicating that
the Controller is ready for programming, then release
both keys.
4.Pr
In automatic scan mode, press any key other than ENTER
key will exit without programming,.
it will emit the next
or the previous POWER key code.
press any key or no key was
pressed in 30 second, manually scan mode will be
automatically exit.
ess and release the Mute key to enter automatic scan
mode. And the remote will automatically sending codes
to the device per 2 seconds.
5.When the device turns ON, press ENTER key to
program the Controller with the new code, saving it to
EEPROM and exit.
6.Press POWER key, If the device responds, no further
programming is required. If the device does not
respond repeat steps 1 through 5.
7.After searching the entire data base, this mode will be
automatically exited and led will blink for 3 times. The
codeset is not saved to EEPROM.
Universal Remote Control
Owner s Manual 33