Filter
Top Products
14
First installation
Automatic programming
Automatic programming of the TV set is started the first time you switch it
on. Follow the menus.
By tilting the OK button in one of the arrow directions, you
can choose the settings ...
... and confirm your settings by pressing OK. You then go
to the next menu.
Back to the previous menu.
1. First you have to select the menu language.
2. By pressing the OK button, you can call the menu “Connect antenna(s)
for“. If you want to receive digital stations via satellite, then choose
“Satellite DVB-S“ - confirm using
the yellow colour button. If
you also want to receive digital
terrestrial stations (DVB-T),
then select “Antenna DVB-T“.
Also select “Antenna/cable
(analogue)“ - this way the standard
analogue stations can also be searched for and saved. If you can receive
digital stations from the cable network, then select “Antenna DVB-C“
using the yellow colour button.
3. For the country-specific station sorting, enter the location.
4. If you have selected “DVB-T“, you then reach the menu “Antenna DVB-
T“. If you use an active antenna, then select “yes (5V)“.
5. In the “Select satellite installation“ menu, make the selection that
corresponds to your satellite antenna installation.
Note: If you have any questions on how your satellite antenna
installation is configured and on the antenna settings, consult your
antenna installer or your specialist dealer.
6. Select the satellite the antenna is directed at, such as ASTRA1.
If you only receive one satellite...
7. In the following menu, specify whether the station search should take
place in the high and low band (“Yes“) or only in the low band (“No“).
Note: For most satellites, a station search is required in both bands.
8. For the low band and high band, the standard frequencies 9750 MHz
(9.75 GHz) and 10600 MHz (10.6 GHz) are preset.
If your satellite antenna is equipped with an LNC (LNB) with a divergent
oscillator frequency, specify the corresponding frequency for low and
high band respectively. Note: The correct display of the received
frequencies in the “TV menu – Stations – Manual adjustment“ depends
upon this setting.
9. You should receive a picture with sound with the settings previously
made (only for ASTRA 1 and HOTBIRD). Then press OK.
10. In the “Pre-programming“ menu, select the factory-set pre-
programming to programme the satellite stations quickly.
To ensure all stations that can be currently received are searched for and
saved, select “No“ at this point.
Symbol rates: The standard symbol rates 22000 and 27500 are preset.
If you would like to receive stations with different symbol rates, specify
the corresponding values here using the numeric buttons on your
remote control.
11. Press OK to obtain an overview of the settings with which the
automatic programming is to take place.
12. Press the OK button again and the station search will start. The TV set
searches for, sorts and saves all the TV stations that can be received,
according to your settings and the antennas connected.
13. When the TV stations are saved, you will receive a corresponding
message.
14. Press the OK button and the set then searches for the radio stations.
15. The TV set searches for, saves and sorts all radio stations which can be
received with your antenna system.
16. Then log on your video equipment, decoder and audio system using
the connection wizard and connect these to the TV according to the
connection diagram displayed. If you want to connect other equipment
later, you can find information as of page 32.
You can repeat the initial installation at any time, e.g. after moving house.
Call the index using the INFO button (in the TV mode, if no menu is
opened). Select the index item “Repeat initial installation“ (you will find this
listed separately before the letter A). Press OK to start the initial installation.
Note: For DVB-T stations in UK the stations are tied to “Logical Channel
Numbers” – “LCN” and sorted from 1–799. Digital station without “LCN”
are stored from 800 onwards. Analogue stations are stored from1001.
Station sorting
Note: not with DVB-T stations in UK.
You can change the station sorting that was carried out automatically later
at any time, see “TV menu –Settings– Stations– Change stations“.
OK
3
3
First installation wizard
Proceed
Back
OK
Connect
Antenna/cable (analogue) (to ANT TV)
Connect antenna(s) for
Antenna DVB-C (to ANT TV)
Antenna DVB-T (to ANT TV)
Satellite DVB-S (at ANT SAT)
OK